Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
hello,
i am using nrf52840 with sx1276 module i am using an library which consists of c and c++ files i want to complie both the file but when i complied the following c...
Hello!
I think I have the below problem, except I am using NRF52840 and therefore PCA10056. I am using SDK14.2 and the alpha softdevice. I am aware these are out of date...
Hello everyone, I would like to ask about the examples of openAMP in nrf5340. I only saw examples of network core in nrf\samples\nrf5340\multiprotocol_rpmsg. Where should...
Hi. I am a beginner with nrf52840. Trying to get SPI and an I2C peripheral working at the same time using the SEGGER Embedded Studio. I have working version of both the I2C...
Hello,
I am using the nrf9160 to develop a cellular product but am seeing inconsistent end-to-end connectivity results. For the nrf9160-dk and a custom board based on the...
Some transciver can improve RF performance like output power and EMV, through supply higher DC voltage. Did nRF52840 have the same characteristic with BLE? Is that high votage...
Hello,
I have a questions on the ADC and GPIOs front end input resistance over operational temperature range, as our final product operating temperature shall well beyond...
Hi,
we are developing a custom board based on nrf9160 that include CAN bus. When updating nRF Connect SDK from v1.4.2 to v1.5.0 we can not get CAN-bus up and running again...
Hello,
For our device we are using a NRF52832 and SDK version 17.0.2. It only has one Button connected to P02. Due to needing the device to be water resistant the decision...
I built the mouse BLE example .
In Windows 10 "Add a device" detects the Nordic_HIDS_mouse device and then issues the
challenge Press Connect if the PIN on Nordic_HIDS_Mouse...
Hi Everybody,
I am working on USBD keyboard.
I used USBD example for implementation.
I changed mouse profile to keyboard profile.
And it's recognized well without...
Is there a way to get the signals of the interrupt for a push-button/interrupt from the pin_change_int example in a logic analyzer software tool? Basically i'd want to visualize...
In bluetooth mesh only 3 channel are used.There is a way to use mesh with an extended number of channel.
Because in some industrial enviroments fading is very heavy and...
I was reviewing the silicon errata for Rev2 of the Nrf52840 and I found this.
[204] RADIO: Switching between TX and RX causes unwanted emissions
This anomaly applies...
I have a smart watch based on nrf51822.but i don't have the customer app.I download the nrf tool box can read the heart rate.But i don't know how to set or sync time,can someone...
