I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hey, I am working with the Matter light bulb sample from the 2.9.1 SDK, which I have modified to support the occupancy cluster. (nRF-52840 and nRF-52840DK)
This worked fine...
We're designing a board using the Thingy:91X as a reference design. We're trying to determine the best approach to antenna tuning.
On the original Thingy 91, it uses the...
Hi Team,
I’m using the nRF5340 Development Kit, and in our project, we have a custom slave device that communicates over QSPI. We’d like to interface this custom device...
My firmware is using SDK 17.0.2, and it includes CPS, battery, and a custom service. Everything has been working fine. The custom service is responsible for sending and receiving...
Hello team,
I am using nrf54l15 dk for the devlopment and want to read the RTC counter to check for how much time my device was in sleep mode.
How to achive this?
Thanks...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
Hi,
I need to enable an input interrupt on nRF52832 and I want to use a GPIOTE EVENTS_IN channel.
During boot configuration, I'm using nrfx_gpiote_in_init function with...
There are two NUS services here, but only the second one can send data through the RX characteristic. I've checked the source code and nothing has changed. How do I delete...
Hi, I want to achieve high speed data transfer between NRF7002 DK with other development board. Therefore, I want to using SPI4 with 32MHz speed. However, I found out that...
I am currently developing a firmware application on the nRF5340 where I need the device to function in dual role :
As a Bluetooth Mesh Node , communicating with other...
Dear Nordic
I use nRF5 SDK BLE_Central / uart to connect our custom peripherals by address, and I found that it seem need to 4~5 seconds to finish connecting
Here is the...
I have modified the NUS-CDC application for the Dongle so that I can now scan, report available Peripherals, and connect to a specific one. I need to be able to cleanly disconnect...
I'm doing development on a very old project with the NRF51 Development Kit with S110 8.0.0 soft device and having trouble finding sample code and documentation on nordicsemi...
So I got me one of these
and after a day of making it work on windows I was able to lunch visual code from wsl and compile. the next day I found how to make a flash with...
Hello Team,
I am currently using the nRF54L15 DK with NCS version 2.9.0 for development and compiling code for the nRF54L10 board.
I am trying to implement FOTA updates...
