hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
I am using UART with interupt on a project where I communicate over RS-232 with an external circuit. This circuit keep TX low until it has received a reset command from the...
Hi,
I'm beginner here.
Could you guide me how to check that my nrf9160 custom board is working?
Should I program it with any firmware before programming with my application...
Hi,
I have merged nrfx_spi and ble_app_uart examples. I am working with SDK15.3 on a nRF52832 based ISP1507. I seem to be able to transmit the data stored in the tx buffer...
hi ,
i am trying to make a project based on detection using ble 5 on raspberry pi 3.
plz help me with selecting correct and most appropriate ble 5 dongle for good range...
Hello, Dear Support. I try to build BLE Mesh from several nRF52840 Development Kits. I use example [serial] from SDK for Mesh v3.1.0. After building solution in SeS and starting...
Hello:
I am able to compile, load/flash successfully for my BLE + FreeRTOS application to my nRF52840 DK board. However, I am not able to start or pause execution of the...
Hello.
I am trying to migrate from sdk 11 to sdk 12 and I am having difficulty in adapting the device_manager.h functions that I am using in my code to the peer_manager...
Hi
I would like to be able to (force) stop characteristic notifications at some point in time.
Imagine a smartphone connects to peripheral and enables characteristic notification...
Hello,
I wanted to test the range of long range bluetooth using two nRF52840 USB dongles with the blinky example firmware of the nordic SDK 15.3 combined with softdevice...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I have very basic query...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
RESETREAS will give cause of reset. But for...
Dear Team
I use the Lwip_mqtt_publisher example from the SDK 15.3 with a PCA10056 board.
Also, I used an Ubuntu 18 Instance(IPv4, I used 6tunnel) to run the Mosquitto...
Hello sir ,
I have conneccted an BLE400 dev kit to an swc J-flash device. And i can't erase it.
Tried with nRFgo Studio on windows 10 an with linux nrf cmd line...
Hello,
I am using the chip nrf52840. I am trying to configure three pins (P0.09, P0.10 and P0.11) as output pins and I am trying to make set and reset functions for them...
