Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
I'm trying to develop from the Linux command line, using arm gcc tools, for the nRF52 Development kit, and can't get the startup assembly file assembled to an object file...
I am preparing my product for radio tests. There is a radio test example in the NRF5 SDK 15.3.0 that requires a UART interface that sends CLI commands to the chip. However...
Hi,
i am trying to read ADC value from my nrf9160 dev board, i can get the exact value upto 2.5v, if i go morethan 2.5v it decrease the ADC value. my values are
voltage...
I've used the nrf_inbuilt_key_write to store certificates/keys in the past, but I am still unable to do it using the "AT%CMNG" modem command.
I can list and delete items...
I attended Nordic Tech Tour - San Jose (Cupertino) on June 11. I did not receive a link for the presentations, as was communicated. Please advise how I can get the Tech Tour...
The BWG832F DK Bluetooth Gateway comes with a board that says that it can be used to program the Bluetooth module. The software recommended for this is the Nordic nRFgo Studio...
Hi everybody,
I'm using nRF52832 on a custom board mounting a BME680 sensor.
I'm running a third party library for the usage of the sensor (namely BSEC Library), and it...
Hello everyone, After having designed a pcb by taking the scheme proposed by the datasheet, I uploaded by the Black Magic Probe, the example code of the SDK "receiver Radio...
Hello,
I'm using the watchdog and i'm feeding it in my main loop :
I tried with
#define NRFX_WDT_CONFIG_BEHAVIOUR 1
and
#define NRFX_WDT_CONFIG_BEHAVIOUR 0 ...
Hello
I am using nrf52840 and am trying to determine the parameters of a voltage divider using the SAADC. Vin is the VDD voltage of the chip, R1 is 4640 ohms and R2 is 38600...
Hello Community,
I successfully build and run mqtt_simple it works fine.
I edit the code
//////////code///////////
void main(void) { u64_t start_time_mqtt; while(1...
Hello,
I am having an issue with the GPS on the nRF9160. I have been developing a custom program that will switch between NB-IoT and GPS when an interrupt pin is triggered...
Hi.
I am curious to know if it is possible to use the ANT-only Softdevice with the Zephyr RTOS. The goal is to create a BT BR/EDR + BLE 5.0 + ANT+ device all on the same...
Hi,
What is the maximum frequency that i can capture on GPIO port of nRF52840 ?
I'm planning to capture a frequency of 32MHz from a sensor on GPIO pin , can I do this...
