Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I have created a project with nRF52840 DK that reads sensors data and transmits them with BLE UART to my smartphone. Everything works fine.
Then, I tried to do the...
i am working on mesh application using two nrf51822 and one nrf2832. I started from light-switch examples. nrf51 set as two server and nrf52 as a client . In server side integrated...
Hi all,
in the datasheet of the nRF9160 is mentioned, that the same antenna can be used for LTE and GPS.
Page 364, chapter 8: GPS "Dedicated GPS antenna or shared antenna...
I'm using nRF52840 with SDK15.0.0
Following this tutorial : https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-characteristics-a-beginners-tutorial...
hi,
I'm trying to add a new BLE service to my device. I've followed the instructions in tutorial : devzone.nordicsemi.com/.../ble-services-a-beginners-tutorial , up to step...
Hello,
I have just started working with mesh and I'm using the 0.9.2 Mesh SDK. When I use the Serial interface (nrf_mesh_serial) I don't see any function about rx or rx...
Hi,
I am currently using two nRF52832 SDK boards to implement text message exchange with another nRF52832 SDK board via BLE Mesh SDK 3.1.0 and nRF5_SDK_15.2.0.
the data...
Hello!
I currently have 2 nR52DK using SDK14 and SDK15:
1) Beacon based on the beacon example
2) Central based on app blinky central + multirole
Then, I modified...
Hallo
I'm using sdk12 , S130 on NRF51822, so far successfully updated application, soft device and BL, however
lately after changing the size and starting address for...
Someone have a example of reading orientation sensor in javascript/HTML of the Thingy:52 equal of the github Nordic Example? github.com/.../Nordic-Thingy52-Thingyjs
Hello, I have a problem with staring "Run" in the "debugger mode" . I used Rigado evaluation board with BMD300 (nrf52) and also work with nrf5 SDK_15.3.0 Examples. Sometimes...
Hello,
I have 2 PCA10056 DK (with nRF52840), my purpose is to check the serialization between App. chip to connectivity chip
I have 2 problems on in each chip:
1. App...
I'm using the code below to enter lp mode;waiting for rtc wake up interrupt to wake up the mcu;
Now I need the app_timer module to do more things ,so I add app_timer lib...
Hi,
I'd like to add a cli command for entering DFU mode .
I'm using nrfConnect on a PC with USB.
When pressing the IF/BOOT button, I can enter DFU and can update the...
Hi,
I am using IAR embedded version 7.40 and my board is nRF52832 PCA10040,while i was checking devices list in IAR IDE under NordicSemi i can see only nRF51 series devices...
