Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
We use the Development Kit PCA 10056 from Nordic (Ver 1.0.0).
When we test different SDK 15.0 - Examples with different configurations we allways expierience following error...
Hi,
I have make a package through nrftil,and I set the version of the app.DFU works well.
1.I wanna read the dfu package version.Can you offer the order?
2.I wanna know...
Hi!
Just to make sure - if I set
advdata.include_appearance = true ;
to
advdata.include_appearance = false ;
inside
static void advertising_init (void)
I simply...
Hi
I have implemented the Nordic Uart Service on the evaluation kit and now I would like to track the data troughput from the dongle to the board with different settings...
Hello,
I'am working with a Taiyo Yuden Bluetooth Module "EYSHCNZWZ"
This Module include the LC Network for DCDC use and the 32.768kHz X'tal.
I'am using Arduino and...
Hi all, I tried to modify the OpenThread's source codes(Just modify an API) and then built them.
Run the build_gcc_libs.bat script to build all of the libraries. That...
Hi:
I use nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_buttonless_dfu.
I want to add flash operation.
The code is as follows.
mian()
{
...............
Hi,
I am developing on a nRF52832 with S132 softdevice using Segger and SDK15.2.0. I am doing some tests with the Flash memory, and my goal is to have some const variables...
We are preparing an application to enter production and seeking to harden it to protect against unexpected system lockup.
The application is a datalogger peripheral based...
Hi,
In the Light Switch Example, on-off instruction was send to either even or odd address, may I know how can I cancel this action so that I can send the on-off instruction...
Hi,
I am using nRF mesh Android app version 1.0.3 and nRF mesh IOS app version 1.0.2
I have flashed the devices with light-switch example application under nRF5 SDK for...
Hi, I have pca10059 dongle. I soldered goldpins to swdio and swdclk lines to be able to flash it using external nrf dk. So I connected external jlink programmer and was able...
Hello, I just wanted to share a problem I encountered and make some suggestions : I lost some time looking for a TWI problem while it was actually related to the pin reset...
Hello All,
I am using NRF51822 controller in my design.
I want to monitor battery voltage using ADC pin with voltage divider.
I have LIPO battery with 3.7V and 200mAH...
