Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Greetings,
Continuing on from a previous question , I'm now able to update the firmware via the secure UART DFU.
One thing I've noticed is that if I enable the RTT nRF_Log...
Hi,
I am using the capacitive sensing driver example given in the SDK(version 12.3) and it works fine. I want to extend the code to ensure that the SoC goes to sleep for...
I have seen exaples using the Raytec MDBT 40 with ATMEGA32U4 infact adafruit has its own board with ATmega32u4 and MDBT 40.
Can I use MDBT 40 with ATMEGA328 ?
Thanks...
Hi,
I am facing issue on nRF51 s110 buttonless DFU. We are initiating DFU using nRF Connect and the device jumps from app to bootloader. On my Android Phone using nRF Connect...
hello,
i want to ask that is there any tool for reading and writing on flash directly.
e.g tool like extreme burner .i am loking for a tool like extreme burner.for nrf51822...
hello,
i am using ble_app_uart code and in this pwm is also used but when i am enabling pwm my bluetooth connection gets disconnected.
will you please tell me how to use...
I am a student and very new with your product and how to use it.
I just order nRF52840-PDK today via online electronic store.
Please provide complete equipment list...
Hi, I want to OOB pair two equal devices (pca10040 + NFC shield) via NFC. Since its not clear which of the two devices will act as NFC initiator (active) or tag (passive)...
Hi.
I'm trying to upgrade multiactivity_beacon scanner example to SDK 11.
But, there's no config for nrf52(pca10040) in that example.
So, I configured it myself and...
Hello,
I just purchased this device:
www.aliexpress.com/.../32399375500.html
but found out that evaluation board is only a debugger and does not actually program the...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
While investigating connection parameter handling, I noticed the following:
The is_conn_params_ok(ble_gap_conn_params_t * p_conn_params) function in ble_comm_params.c only...
