There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx(the send length is fixed 10 bytes) ...
Dear nordic employee:
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c(pca10040) by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
I want to use the Smart Beacon Kit (PCA20006) and the blink led demo. However it seems that I cannot use the s110 V76 softdevice when writing my app in Keil. However, how...
I'm writing an application which updates the ble advert data at run time. I use the radio_notification callback functionality. Inside that function, the code calls the ble_advdata_set...
Hi, I'm trying to run ble peripheral and timeslot receiver at the same time. I can see ble advertisements and I can connect to the peripheral. I can also read and write ble...
Hi,
Some questions below about the HID keyboard that refer to the example "/s110/ble_app_hids_keyboard" .
What initialize m_advertising_mode value before to call...
Hello,
to reduce ernergy consumption i use the sd_app_evt_wait() function while the twi is sending or receiving data.
i set nrf_twi->address and nrf_twi->txd and set...
Hello,
I have troubles using spi_master_example.
I want to control by spi a slave device from the nRF, I am sending sequences as expected and my slave device answers me...
The S130 SDS 0.5 documents a CODE_R1_BASE of 0x00020000, but I can't get it to work with code at this location. Any SoftDevice API call ends up in the application's SVC_Handler...
Hi,
i use the library app_gpiote to setup interrupts on a toggling external pin(this pin generates a signal which changes from high to low).The external interrupt signal...
Links: ota_profile_pkt_rcpt_notif
As you see,GAP Disconnection,I don't Know how it works.The ble device call disconnection,but ble android phone respones it more then 5s...
Hi, I'm a student at Oregon State University using the nRF51 Development Kit for a project. I can't seem to find any functions for sending and recieving Bluetooth signals...
HI ALL!
I got a question about establishing my own service.
Currently, I can just send my data through the 'hrs' service(by replacing the heart_rate value with my own...
Hi,
I just downloaded the Utility app for the ble apps(nRF518 SDK) checking on my i5 at iOS 7.1.2. I have tried to connect the apps(hr, proximity) of Utility, but there is...
I changed the dfu start address to 0x00 and application start address to 0x8000.
The application use the RTC0 IRQ to count the timer,
but the RTC0 IRQ did not work correct...
I've been successfully using IAR and I-jet with the 51822 and S110. I can build, download and run under the debugger with no problems.
I recently switched to the 51422...