Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hello, I try to do work a ism330dhcx on a custom digital board with a custom board in which there is a NRF54L15 microcontroller. The sensor works on other custom board with...
Hi all, I'm currently evaluating a few different vendors, chips and technologies for an idea I've had. It's a wireless+USB gaming HID, so latency is very important. 1kHz polling...
Hello,
We are planning to use the nRF54LM20A, but we do not intend to implement USB in our design.
For the nRF52 series, the datasheet provides a reference schematic for...
Hello all,
Please let me know which module we can use for mesh networking for home automation project (lighting control through smartphone app),maximum how many devices...
Hi, we are currently implementing DECT NR+ mesh network as part of a thesis, where our one part of our plan was to implement full MAC layer (otherwise its just a full mesh...
Hi,
I'm trying to write a generic tool that lists the attribute table of a connected BLE Peripheral. For each discovered attribute I want to log to the console the attribute...
Hello,
I am trying to determine if it is possible to have those 3 stacks coexisting.
I have an iSP4520 chip, which includes an nRF52832 (BLE and Wirepas) and Semtech SX1262...
Hi,
We’re currently integrating the nRF54 series into a product we’re developing, and we’re using the reference schematic and layout as our guide.
While working through...
Zigbee Add-on (R23 1.2.1) doesn't support octect string attribute reporting which seems to be wrong.
I've found this topic that describes the same issue
and a workaround...
Hi Nordic Team,
We are developing a battery-powered cellular IoT device utilizing the nRF9161 SiP combined with the nPM1300 PMIC. Our primary goal regarding power management...
Hi,
We are updating an older platform with the nRF9151 on an add-on PCB.The platform has very limited processing power and buffer space.
The nRF9151 module with the...
I am using the Zephyr NVS Settings module. In some cases this happens: I try to save a value with ` settings_save_one ()`, which internally calls ` nvs_write ()`.
I debugged...
I'm running into a bit of an annoying situation every time i run ' west flash --build-dir ./build' in the command line. It rebuilds always after a successful build i set when...
Dear Nordic team,
I have a complex question. In my project I use components which operate at 2.25V as well as they expect 2.25V logic levels.
My idea is to use nrf52840...
