Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
Hi,
I'm using the Ellisys tool to capture packets and compare the differences between CIS and BIS. The capture results for BIS show that it is unencrypted, as seen in Figure...
Hello.
We're trying to expose and use the Wifi stack in micropython in our project for the nRF7002. We've managed to get Wifi scanning to work (based on the sample code...
We have developed a hardware platform using the NRF5340 on Nordic's zephyr (version 3.5).
Our current consumption in idle mode is still around 330 µA, instead of the expected...
Hello.
I have a setup in which two nrf52840_dk boards are communicating through BLE. I'm using Zephyr 4.1.99.
Under heavy traffic. the board which holds the 'central'...
Hi, I'm working on the DK for nrf52832. I have a working code for BLE, and another working code for die temperature using interrupt. Now I want to merge them and trigger the...
Trying to set up a PPK(II) to measure the current in my nRF 52833-DK and preparing my nRF Connect for desktop to do so, I notice that this tool is demanding a V7.94i version...
We have an nRF52840 device that is required to do continuous BLE scanning in central role to find nearby advertising beacons and is never required to establish a connection...
we have a custom board with nRF9160, when using GNSS we configured it to periodic mode with 120 second interval, most time it works fine but every once in a while (like every...
Hello,
A quick question about using an nrf9160 (+ sdk 2.5 - modem 1.3.5)
When I activate the following parameters: # LTE-M (LTE-CatM1) CONFIG_LTE_LINK_CONTROL=y CONFIG_LTE_NETWORK_MODE_LTE_M_GPS...
Hey,
I have been using the FOTA download client library with bg95 module for HTTP dfu for a while and works perfectly fine.
Now that I have added a few additions to my...
Hi,
I developed a custom board with nRF52810. Here is my schematic:
Layout:
I can succesfully upload the "ble_app_beacon" example in SDK17.1.0 with softdevice112...
Hello everyone, I hope you can guide me in a right direction. 1. I setup my environment as per https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/installation.html , using...
Dear support i have two problems,
In ncs 2.6.1 i get: error: '__device_dts_ord_DT_N_NODELABEL_red_led_P_gpios_IDX_0_PH_ORD' undeclared here (not in a function) in the...
Hi All.
I am trying to emulate a central BLE module to scan peripherals around, using an nRF52840 USB dongle and nRF Connect for Desktop. The goal is to confirm that my...
Dear Nordic,
I have a Thingy91x. I tried flashing the nRF9151 SoC on the device but ran into error messages. I realized that the nRF53/nRF91 switch was in the nRF53 position...
