This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I am working on a project that uses nRF5340.
We are now looking into designing software update mechanism. As a part of this, on the app core I am planning to move slot1_partition...
Hello,
when creating a multi-image build is it possible to select the optimization level for each image individually?
Below is an example of the issue I am facing currently...
Setup:
nrf connect sdk version v2.1.2
board: nrf52840DK
Trying to send a beacons for half a second whenever I get some specific data on uart, and also send data over...
I have an array of LEDs on my custom board. One of the LEDs is set on a UART0 RTS pin, which is GPIO(0,5), and we are using ground as common. To avoid any conflicts, I disabled...
I am using an IMU sensor in sensor hub mode (LSM6DSV16X, LIS2MDL) with the FIFO interrupt interval set at 30 Hz. The data is sent over BLE. It works perfectly when using RTT...
I am using the s120 soft device v2.2.1 as a center communicating with a peer using a s110 soft device.
The peer is a black box an all I have is the documented protocol. ...
OK, I'm working with the nRF52832 and NCS V2.6.0, and I have two different actions I need to complete at various times with the SAADC:
Every ~ 3 seconds, I need to sample...
We want use NRF5340 to do le audio application. We got the demo from your website, and find the audio demo, but the min sample rate is 32khz can be set, we want to use 8K...
I am running into a recurring issue with attempting to connect to a nRF52840DK advertising using extended advertising from iOS devices. Connections repeatedly fail to establish...
Hello,
I am implementing firmware to communicate using UDP between two nRF7002.
The sender does not know the IP address, so it tries to know the IP address of the receiver...
Hey,
I'm currently working on a legacy project that uses the NRF5 SDK. Rewriting the project to use the nRF Connect SDK would be tedious, time consuming and likely to introduce...
Hi,
I am working with the Matter Light Bulb sample . I have come across a problem where I can not compile my firmware if I implement the occupancy sensor cluster using the...
Hi,
I'm trying to run `ncs/v2.6.1/nrf/samples/net/azure_iot_hub` sample with `native_sim` board:
1. certificates are configured (compiled in)
2. `zeth` interface is...
I want to use the signing script as mentioned Technical Documentation (nordicsemi.com) , however, with NCS, this script is not automatically being picked up during the build...
Hello,
We have many nrf9160 based devices currently on the market running for our customers. These devices are facing some problems that we are trying to debug right now...