Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hi,
I tried building and debugging the sample "https_client" using the method described here . But debugging fails. Debugging stops prematurely because the source file cannot...
I need to be accurate to five decimal places.
Use nrf52840 and ses.
Test code:
Execute d=atof(mm)/60.0 result 0.70693.It's right.
But e xecute d = 0.70693+22 result...
I am trying to use SAADC.
When viewing the contents of nrfx_saadc.c in SEGGER IDE all the code is greyed-out.
I verified it is enabled in sdk_config.h:
// <e> NRFX_SAADC_ENABLED...
Hi everyone,
I am currently attending the nRF Connect Fundamental Course.
As you can see from the picture below (taken from the Course material), there must be the chance...
Hello DevZone,
I was tinkering around with the speed of the TWIM0 module in the nRF52832.
I have a cheap USB logic analyzer to help me display the waveforms and I made...
Hi,
I am using NRF52832 development board , to which i have interfaced LIS3DSH accelerometer sensor(3.3V i2c)
when i configure it for 1600 sampling rate and all the...
Hello,
I am using nRF Connect for Desktop v3.12.0 with Programmer v3.0.4 on Mac. When I program mfw_nrf9160_1.3.2.zip on the nRF9160 dev kit, it works, but when I try on...
Hello! Very quick question. The available Zigbee and ZBOSS NRF documentation repeatedly to code examples that I am unable to find. The only examples I have are at nrf/samples...
I've previously successfully done interval advertisements using a SoftDevice with Nordic's previous (non-Zephyr) sdk, but I'm having issues replicating it on Zephyr.
Our...
Hi, I am using the nRF52840 with the softdevice s140 6.1.1 with the SDK 15.3 with FreeRTOS. Sometimes after collecting data for a around a day the device sometimes crashes...
Hi,
It has been a while since I looked up on different resources to get SPI slave transaction example and I finally found on the `nrf / samples / tfm / tfm_secure_peripheral...
Hello,
I have three questions regarding FEM.
#1 According to the following URL, FEM function is supported only for nRF52 series.
Would the FEM function be available...
Hi We are working on a new product that includes NFC, When we measure the voltage level we do not reach more than 600mv. The matching was done by capacitors: using a 2uH antenna...
Dear all,
I could happily flash my firmware to my nrf52840 upon pressing reset button. When pressing the reset button the diode on the board started to beat red and via...
