I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
We are using the Softdevice controller from the nRF Connect SDK on the nrf5340 processor and have implemented the commands to read and set the tx power level in the controller...
I want to take readings from SHTC3 temperature and humidity sensor from a custom board. Using I2C master as nrf5340 how can I take readings from slave custom board. Please...
Hi guys.
With the nRF52840 DK(PCA10056) running the Running Speed and Cadence Service (RSCS) example, the nRF Connect app on my Galaxy S10/Android 12 was able to scan the...
For emission testing, we need to be able to use some DTM commands (such as: transmitter test) inside our normal firmware.
The normal firmware uses the softdevice for BLE...
My project requires two sensors to operate on the same i2c bus, one of which is a display and the other of which is a touch sensor. And I have a problem where, if I test both...
Hi Everyone,
We are using nrf51824 for our project. As segger embedded studio has free license we have to migrate Keil project by following the article Segger Embedded Studio...
I have vsc version 1.66. I'm getting the following notification:
File changes watcher stopped unexpectedly. A reload of the window may enable the watcher again unless...
Hello,
I am using the https_client example for Thingy91. Everything was working fine until I tried to change the website to send https requests to (from example.com to google...
Hello Team Nordic, May I ask for your advice on how to build one nRF52840 to have two different UART connections to two different devices? May I ask for the any code examples...
Hi,
I am trying to integrate custom protobufs into the asset tracker project. I am referencing the zephyr/samples/modules/nanopb project for the same.
But I am getting...
HI ,
I'm trying to open terminal/command SDK v2.0.0 from toolchain manager (working with nrf connect for desktop v3.11.1) but it doesn't open.
while on SDK v1.9...
I'm just trying to make a simple communicatión between my nrf52 dk and my mobil using Serial Bluetooth Terminal app. I took the ble_app_uart example and I added a function...
Hi,
My project is a host micro (STM32) and a nRF52840 (controller mode) to implement a peripheral. My previous project (STM32 BLUENRG-M0 and host micro, HCI SPI interface...
Hi,
I'd like to add live audio streaming to my product, The current product consists of a sender unit and a receiver unit. Both using the nrf52833 (I've already bought 500...
hey guys i want to implement two separate application programs on the same chip.
Say Application1 is stored in address start_address1 to end_address2 and Application2 is...
