hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
Hi,
Basically, the setup of the mesh network is as follows,
There are END NODES based on sensor server model.
There are RELAY NODES based on the sensor client model...
Hi,
I am using Zephyr3.0.0 to validate AOA CTE sampling.
Firstly, a s below is the official data format. Nordic Semiconductor Radio peripheral provides 16 bit wide IQ...
Hi,
I am able to successfully build and flash the Matter Light Bulb sample onto my nRF52840 DK.
I am now getting ready to configure the firmware for use on a custom board...
Hi,
NCS1.9.1,nRF5340DK, VSCode，
see code, timer_lms==1000 spend 1000ms
but if start i2s
i2s_audio_init(); //this line will Slow down the time
timer_lms==200 spend...
When i try to use SES to build my project.there is error.The enviroment i confige as descrblied. them i use toochainmanger in nrf connect tools,the error is as the same as...
I'm trying to determine how to get a Linux timestamp for a project using nRF9160. It looks like the mktime() function is not supported. Any suggestions?
thanks!
I'm running into a weird bug where the first 4 bits received by my SPIM are always 1 - the next 64.5 bytes are all correct though... I've built 3 FWs out of provided examples...
Hi guys,
I have developed an app to read data from some sensors and notify the central with a frequency of 100Hz. It seems to work but I would like to share my approach...
Hello,
We are trying to get UART communication between nRF9160 and MSP430.
MSP430 need to send out a sensor data through UART.
We are using 1.9.1 SDK, and Visual...
Hi,
Is it possible to remotely execute a command that would force a BLE node into indefinite sleep or standby mode?
I am working to build out a BLE mesh network, where...
Hi. We have a custom board featuring 4 FSR sensors on it, based on the Nrf52810. Initially i tested those boards and the sensors using an STLink-V2, along with the Arduino...
hi thanks for you heip!
i want use \nRF5_SDK_17.1.0_ddde560\examples\peripheral\radio_test for radio test, here is the questions:
1、could this example can send prbs9 wave...
Hello!
I have to decode signals from two quadrature encoders. I know nordic has a driver for this, QDEC, however. there are a couple problems:
1. I need to control two...
Hi
Is there some example, how to use CAF and sensor_manager. I try to use BME680 sensor with CAF, but i'm somehow stuck. I got the sensor manager working and I see sensor...
Dear, I copied the Button sample project to another drive i.e. G. I added the overlay file. The file is attched. The included file is shown on ltop left corner side under...
