hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
Hi,
We are using nrf52840 for custom design and we have replaced the mx25r6435f qspi flash with Cypress S25hS512 qspi flash. We configured the flash as below in the dts...
Hello,
We have nRF52832 devices in the field, and one of the leading causes of warranty returns is that flash of nRF52 is completely erased. nrfjprog --readcode and --readuicr...
Hello,
We have a problem that affects a few devices (< 0.1 %) in mass production. The devices are flashed, boot up and pass tests and get shipped to customers. Some customers...
1. all files were successfully attached
2. there is no syntax error, there are only warnings
3. Please help me to resolve this problems as soon as possible.
Good day everyone !
Can thingy 52 itself be used as a location tracker, from Received Signal Strength Indicator(RSSI) . Does it have this function ? If it does, may i...
Hi all,
First of all, this is a new field for me, so I'm quite a beginner here. I'm connecting my ESP32 to wifi and I want to send somehow the IP it connects to, to the...
Hello,
In my application (SDK, 16.0.0, nRF 52840) I need to enable the DFU service after initialization, which I do by exposing a custom service "DFU enable". This in turn...
I'm currently using Zephyr with Nordic Segger v5.50c.
Most of the code uses NRF_LOG, NRF_ERR statements which are printed to the Nordic Segger terminal.
I also configured...
Hi,
We are trying to update the S112 softdevice on nrf52811 over serial DFU but it's not working and throwing the below errors.
We are using nRF5_SDK_17.1.0 and soft...
Goodday,
For some reason my nrf Connect Programmer stopped working after doing the latest updates. To test I took a brand new dongle, Programmer picks it up but does not...
Hello, i have send my program with my DKnr52840 on my module 805, (the example peripheral Uart) now i would like to make my com with putty or other software but i'm going...
Hello,
The company I work for uses an nRF52840 PCBA for one of its project. During production, the board will be placed under test using a custom-built fixture. Due to the...
Hi,
For my application I am supposed to evaluate if nordic SPIM & SPIS drivers are working on interrupts..? In the driver file "nrfx_spim.c" I observed the below code...
Hi,
I have some questions regarding DFU:
Does it have its own BLE hardware?
Does it have its own processor? Or it's part of the main one?
Can we synchronize between...
Hi all,
struct spi_config {
uint32_t frequency ;
uint16_t operation ;
uint16_t slave ;
const struct spi_cs_control * cs ;
};
in documentation, it says...
