hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
Hello,
Using sd_ble_gap_adv_set_configure() with ble_gap_adv_params_t I observe that the actual time when the BLE_GAP_EVT_ADV_SET_TERMINATED event is raised is earlier to...
Hi All,
Likely because I am still quite new to this, but I have started with MQTT simple example and whenever I do use GuiConfig to make mods, it saves them to
proj/build...
The disccussion here
https://devzone.nordicsemi.com/f/nordic-q-a/24592/my-nrf52-nrf51-dk-kit-doesn-t-work
has been closed.
I followed step 4 and it took a few tries...
Hi,
I use a Segger JLink EDU (the big version, not the mini) to flash some custom boards. This used to work fine until I upgraded nRF Connect and got Programmer v2.0.
...
Dear sir/madame,
By an accident I selected Power Profiler Kit II when I wanted to download an application to “PCA10056 DK” . After that ‘download’ Power Profiler Kit II...
Hello,
I'm using NRF52832 as a controller for cellular modem and used the AWS IOT supplied with the NRF Connect SDK.
I want to use the AWS FOTA and I'm a bit lost, I added...
This builds on a previous Forum Post that was closed out.
There is a peculiar issue with the NRF52840 SAADC sampling. For an unknown reason, triggering the SAMPLE Task in...
I have a nRF5340 with a UART that connects to a circuit that is not powered on until it is needed by the application. So the UART must be powered off until the application...
Hi,
We are developing cycling trainer, so we use BLE fitness machine profile. Our functions are basically completed and we are testing with some VR cycling windows or desktop...
Hello, please help if you can.
Once connected. I am asked to program the board when trying to use BLE from nerf connect.
However, I get the error: Error while setting...
Hi All,
According to the title,how should i do?
I want the project on the left to have a dependencies under main like the project on the right.
Best regards,
...
Hi all,
Currently working on a project using the nRF52DK and nRF52832 that will be powered by a CR2032 coin cell battery.
I want to measure the battery level from the...
Hello.
I'm working with nrf52833 custom board and S113 softdevice for Buttonless DFU.
The pieces of information below are my FLASH & RAM address settings.
(Reference...
I'm trying to duplicate the boot behavior of a Thingy91 on a custom board, i.e. SW4:BOOT and SW3:BUTTON on power up, but the switches available use different IO. I'm wondering...
Hello, I am pretty new to using the Nordic products and was wondering if there is a simply way to write a text file from the nRF52840 to a pc. The system is required to log...
