I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
I've 3 FTD nodes (nRF52840 SoC), the network between the nodes and the UDP message transfers are been done successfully.
I want to split and send the messages between...
Hello,
I am using your NRF9160 chip and need Nordic team help. I have refer to your FOTA sample, I am looking for a safer solution for updating code. On my board, I use...
Three software seems to perform OTA DFU: nrfutil command line, nRF connect from desktop, nRF connect from mobile
Do I need all three of them? Are they part of Nordik SDK...
Hi,
I am using an Adafruit nRF52840 Express with a sensor board attached to it. I'm noticing that my sensor IC is reading about 3-6dB higher noise in the 10-50Hz range ...
Hello,
I want to program and debug a custom PCB using the nRF52832 SoC and nRF52 DK. I plan to use this setup:
From what I understand, the GND detect will cause the...
Hi Nordic team,
We are busy testing the throughput of the nRF9160. We are having issues installing the NCS at this stage, and was thus provided with a HEX file of the Serial...
Hi Nordic engineers,
I am using west to build the nRF NCS, my own project which is adopted from samples. Using Powershell (win10) to run west commands as below.
I need...
I tried the "ble_app_hrs_pca10040_s132" example from SDK17.0.2 on an ISP1507-AX and wanted to access the Heart Rate Service to read out Heart Rate and Body Sensor Location...
Hey guys ,
I am trying to merge ble_app_uart code with RTC peripheral code . RTC code works fine when I try it on SDK but after merging with ble_app_uart code it doesn...
Hi,
I have a question about the connection handling when we have two connections to a single smartphone.
The smartphone runs two Applications:
App 1: Acts as central...
Hi,I recently started using a PPK2 board and at first had no trouble setting it up with the Power Profiler Software from the nRF Connect for Windows.
What I realised is...
Hi,
nRF9160 in nRF9160DK with NCS v1.6.0 and master, power consumption measured by PPK2.
With CONFIG_SLM_EXTERNAL_XTAL=n nRF9160 average power consumption is ~7uA after...
My use case is that the nrf9160 is running as a serial lte modem and I have a host controller that is controlling the ENABLE pin. VDD will always be powered so can I leave...
