I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I have applied the errata 171 workaround to a zephyr code base with an MX25 chip and set the speed to 96MHz - when I run the application (engineering D silicon) with a scope...
Hi
I have used ble_beacon example to configure DK board as beacon here i wanted to pass custom data inside the code and print those array code on output debug console to...
I have an embedded Linux platform which uses an nRF9160 connected via UART. The nRF9160 has been loaded with the serial LTE modem firmware, version 1.3.1.
I've been experimenting...
Hi!
I'm developing the NRF9160 target from a raspberry Pi. The problem is that I need occasionally to perform modem firmware upgrade, and I can't figure out how to do it...
Hi. I am currently using an nRF52840 DK board and SDK 17.0.2.
I have add a custom characteristic in the heart rate service sample code.
The characteristic is shown on...
Hi Nordic,
I am using your official board nrf52840 to develop my application based on the ble_app_uart_peripheral example. BLE communication and the spi interfaced sensor...
Hi, I'm working with a nordic thingy:52 and SDK thingylib on Android.
The issue I'm facing is that the real sampling frequency, compared to the one indicated by the SDK...
Hello,
I try to use the ASSET_TRACKER application with NB-IoT/ Vodafone in Netherland. Vodafone uses UDP/IP datagrams protocol. is it possible to modify the asset-tracker...
So, we are using NRF52811 with external 32MHz xtal and also exeternal RTC crystal.
Every now and then we are unable to pass tests of the programmed firmware because the...
Dear Sir/Madam,
I have already developed an RF communication device with an NRF24L01+ device. And I want to migrate to nRF52833-QIAA-R. For that, I have the below questions...
I'm using RTC to wakeup every 500ms, I have Watchdog enabled but after a while (about half.. or an hour...) it will not wakeup anymore and watchdog will not reset.
I measured...
Hi, we programmed the nRF52840-DK with ble_app_hids_keyboard demo (s140) and tested with different BLE keys under a Linux PC. It worked. Tested the same configuration with...
Hi,
I have some code that normally uses nrf_crypto with the cc310 or cc310_bl backend. I was writing a unit test for this code which compiles and runs in Linux/WSL. Since...
Has anyone written a utility to dump the tables of contents (i.e. directory of files) and
an entire file with record keys:contents to a host operating system file to a file...
Hi,
I'm working on the bootloader part of a project. Using nrf Connect, the integrated MCUBoot bootloader, trying to figure out how all the parts fit together. Running into...
