Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
I am debugging my applications transitions to SYSTEM_OFF and back again. I am connected to the debugger so I am presumably testing with "emulated system off" which is just...
Hi all,
I wrote a nice library for using an offboard SPI flash chip and am now trying to port it to our master code which runs on freertos.. I wrote the library starting...
hello ,i am using sdk16 with nrf52852 DK i can be able to get time using that nrf calendar example. Now i want to sync up the mobile time with Dk every time i connect with...
Hello, i'm developing some boards with nRF24L01, everything was going fine, i was able to write and read payloads back and forth using modules mounted on 4 different hardwares...
Hi,
We were trying to bring up NB-IOT with a Jio SIM ( India). Seems it is able to connect to network, but no data connection. The sim vendor said to us we need to use ...
Hi all,
I cannot manage to get a proper System Off consumption with the nRF52840.
I use this setup, with devkits as the DUT (powered through "External Supply") :
...
Hi all,
In my current project I have 7 sensors, each hooked up to an own nrf52. I am polling between 8 and 28 byte(depending on operation mode) of data in 10ms intervals...
I created a copy of bluetooth/peripheral example and copied the nRF5340DK board files to make my custom board definitions. The guideby Øyvind A. Sandberg is really good here...
Hello All,
I'm interfacing a temperature sensor ds18b20 with nFR52840, which uses one wire protocol.
I'm using this repo https://github.com/DSysoletin/nrf52_ds18b20_example...
Hello! I wrote my own version of the bootloader for nFR52832. If I go into the loader, check the application and switch to its execution via nrf_bootloader_app_start (), then...
.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol nrf_drv_clock_init (referred from main.o). .\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol nrf_drv_clock_lfclk_request...
I need to adjust the Flash and RAM to accommodate bootloader and Softdefice and read the tutorial at the link https://devzone.nordicsemi.com/nordic/short-range-guides/b/getting...
- I reviewed Android-nRF-Mesh-Library code, and i saw this logic: first, it used Provisioing Service, when provisioning is completed, it disconnected with nrf board, and then...
Hi!
I'm developing code for Central device on nRF52840. SDK 16.0.0 SoftDevice S140.
Peripheral is a Bluetooth mini printer. I can connect to it and print. But when I try...
Does SoftDevice S113 use interrupt priority level 4, or a re the actual S113 interrupt priorities 0, 1 and 6?
As I understand it, this says S113 uses priority levels 0...
