Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
From my understanding, I should integrate the LwM2M Carrier Library connection as the first step in the boot process and once I have received the LWM2M_CARRIER_EVENT_READY...
Hi Team,
If we send 20 bytes of data to AES-ECB 128 bit (CC310/ mbed TLS) Crypto engines for Encryption/Decryption due to bytes padding, how many bytes it will become...
With iOS and Android smartphones we are advertising some ble frames.
With our own code on the nrf 52840 we get around 2-4 advertisements each seconds on the nrf 52840 chip...
Hello,
I am trying to use the peer manager on a nRF52832 acting as a peripheral with both bonding and legacy pairing on SDK 16.0.0.
The application configured with bonding...
I am using version 4.1 of the Mesh SDK and version 16.0.0 of the nRF5 SDK on Windows. I was able to successfully generate the ninja build files using CMake. However, when...
Hi,
I'm interested in multiprocol examples and I'm trying to compile examples provided by the latest sdk for nrf52840 mcu.
IAR 8.x doesn't work I have this error "code...
I have written two functions to write and read data from the flash using flash_fds module. In this way I am calling the function to write the data to flash :
fds_write_record...
Hi there,
I was comparing the power consumption of ble_app_hrs_freertos and ble_app_hrs examples on nRF52840 DK. The average VDD current is 7.4 mA for the example running...
Hello,
I'm in need of turning on and off the LTE link to use the GPS in cases where I can't depend on PSM. The LTE Link Controller library is good for this however I have...
I'm in trouble... My design has 3 SPI devices, and at a late stage I ran out of GPIO so I added a I2C I/O expander before spinning and building my PCB without thinking too...
I'm trying to use nRF sniffer 3 and can't get it to detect the dev kit on Windows or mac. I've installed it into wireshark and see the toolbar, but no interfaces are listed...
Hi,
Can we give a voltage more than VDD+0.3V on an open drain high impedance configured IO pin? By open drain, I mean:
nrf_gpio_cfg(pin_num, NRF_GPIO_PIN_DIR_OUTPUT, NRF_GPIO_PIN_INPUT_DISCONNECT...
Hello, I am trying to follow and understand the MCUboot encrypted image design found here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/mcuboot/encrypted_images...
We are trying to connect to discovered smartphones with a Nordic 52840 chip, with S140 softdevice, discover the gatt table, read and write attributes. Most of the time it...
