Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
Hi,
I want to integrate HID mouse and HID keyboard in a single device. Can you tell me the complete configuration procedure to integrate HID mouse and HID keyboard in a...
I recently got the nRF52-DK for using as BLE Relay evaluation.
I have downloaded following and installed to run the code
- Segger Embedded Studio (v5.1)
- nRF5_SDK_17...
I'm using the NRF8001 with a Teensy 4.0. I've been able to find a port of the Arduino library for the Teensy here ( https://github.com/tato123/nrf8001_arm_support )
I'm...
I saw on the main Q&A page the person answering the Q&A said " one should really put the application in one CPU (the M33) " which I understand the nRF 9160 is the M33 processor...
Hi
I have a BLE project on nRF52832 , I use sd_ecb_block_encrypt to encrypt data, it worked fine until latest migration from SDK14 to SDK17
(which involves softDevice...
I have a similar issue with https://devzone.nordicsemi.com/f/nordic-q-a/58524/nrf-mesh-can-t-see-node-feature
I am using nrf5_SDK_for_Mesh_v4.2.0_src for the light switch...
Hello,
My sck frequency will be 5Mhz.
Accordingly, nrf24l01 + mcu and SPI parameters as Rpull = 10kohm and Cload = 50pF How should I connect pins and which pins ( (ce...
Hello,
Our product is BLE Beacon.
We have developed original software on nRF52832 SOC.
To keep up with your latest technology we transitioned to nRF52810 SOC.
To my...
Hi,
I had a problem while testing using the app_app_uart.
I added custom service and set tx buffer size to 70.
I tested using nRF Connect.
And, i got error message...
I received a bunch of Thingy:91/PCA20035 version 1.4.0 which upgraded the SWF connector for GPS antenna to a uFL/IPX connector which is great. I also have a few PCA20035 version...
Hello,
I'm using SDK for Thread v.4.1.0 along with nRF52840 microcontroller. Starting from MQTT-SN examples I developed a Thread network with multiple nodes, publishing...
The nRF51822 QFAC-R has a drive level of 1uW max for a 32.768KHz crystal. We would like to use an Epson crystal with 9pF load however its max drive level is 0.5uW. What are...
Hi,
I am have programmed my Thingy 91 device with lte_ble_gateway program to collect data from 5 Bluetooth devices and send them to the cloud. This program runs fine,...
Hello Within my Thread network, I have a lot of Thread devices (with a lot of routers). Every now and then I need to multicast data to the whole network (I use the address...
