Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello, a couple of get-me-pointed-in-the-right-direction questions, if you don't mind.
I plan on creating a system with an accelerometer that talks SPI to my Nordic nRF52833...
Hi!
I read that your Thread stack uses a different 802.15.4 implementation than the MAC driver. Is it possible to intercept special broadcast data packets e.g. from energy...
Hi!
I started to modify the ble_app_blinky example. I need to increase ATT_MTU, so I modified NRF_SDH_BLE_GATT_MAX_MTU_SIZE. For this, I needed to increase the RAM of the...
Hello,
I'm using Mesh SDk4.0.0 and SD v7.0.1. I have tested the light switch client and server examples.
Now I want to add some more models for additional functionality...
Hi , i want to change the device name by connecting the device using nrf_toolbox , have a look at my code , you will get what i am trying to do . By the way i am using nRF52832...
Hello Nordic!
I'm developing with nrf52840, s340, sdk 15.3.0, gcc-arm-none-eabi-7-2018-q2 in my customboard.
Recently, I am making ble central module.
I can scan and...
Hi, I have only one question: during the write or erase cycle using fstorage, the cpu is locked? Sofdevice, Interrupts and main application are working also during with flash...
I'm using FDS together with Flash manager, and checked if everything goes alright in flash.
As per doc, I set FLASH_MANAGER_RECOVERY_PAGE_OFFSET_PAGES to FDS_PHY_PAGES....
Hi, I just try to start with the spi master example (nrf5sdk/examples/peripheral/spi) on mus PCA10040 board. I'm able to compile&flash it. It seems to be running (LED1 is...
Hi ,
I working on the getting started assistant setup but got failure when verify the GNU ARM embedded setup , see the following log :
11:32:05.867
c:\gnuarmemb\bin...
Hi,
Just want to ask what will be the effect if I will use an external oscillator (32.768kHz) with a CL nearly at max specification, let's say 12pF.
Thanks.
Hi,
Can we send a message from a Provisioner to a Unicast address in a mesh network?
I'm using nrf52832 and can send orreceive message between nodes in the mesh but I...
Using 4-bit SPI mode on the Display Controller side: SCL,MOSI,MISO ... and DCX (by which the controller distinguishes between command bytes and data bytes). There's no obvious...
