I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hello everyone, I come from the 8bits MCU world and I'm used to program my chip with a debugger like Atmel-ICE. But with 32bits MCU I'm a bit troubled to program nRF82832...
I'm using the IoT bootloader from NRF52 SDK 14.2. When the bootloader has nothing to do and starts the main application, the FDS calls all fail in the main application. When...
We're using QuantumLeaps and want to send a message each time a character is received on the UART command line interface transport layer.
Where in the SDK source code would...
Hello,
I have just purchased the nRF51 Development Kit and I am having extreme difficulty getting any of the sample programs to function.
There are the specifications...
Hi,
I am porting a NCI (Nfc Controller Interface) driver to the nRF52. One of the things I am struggling with is that, when reading from the device, the amount of data...
At first i have tried the simple uart code from nRF52 where i could send the AT commands properly and UART communication works fine between nRF52 and GPRS module.
Next...
I use a development board with nrf52832 xxaa, BLE demo from SDK works. But I created own board but with nrf52832 xxab(less ROM and RAM) and changed configuration in IAR project...
Hi,
I want to use hardware ECB encryption and decryption in 52840.I had tested the demo from nRF5_SDK_13.1.0\examples\crypto\nrf_cc310\aes\pca10056 . However,i can't find...
When using the APP_TIMER in SDK14 I am having a problem with the application stopping.
I was using the APP_TIMER to flash LEDs and watch for timeouts in SDK13. when porting...
in the sdk_config.h there are plenty of definitions, where "31" is used as a non-valid PIN value
This is destructive if you want to use p0.31
For example:
If one uses...
Hello. I want to use the same pin on nrf52832 for wake up and system off, however I have some issues, like sometimes it doesn't wake up or it is needed to press button few...
When I use sdk14.2 nRF52810 ble_nus_string_send to send data to a mobile phone android, the first connection is no problem, but disconnected again after connecting problems...
Edit: I'm using the softdevice S110, 8.0.0, Nrf51822 chip, Keil uv5.12
Edit #2: Added more detail and revised certain description.
What's the problem?
My program...
Dear partner,
1) Our custmer want the spec of S140, I cann't find that on the inforcenter. can you give me one?
2) By the way i want to know where is my mypage case...
I want to have every node carry a copy of the sensor data in every other node and pass these around on update.
Should I use ANT FIT or FS? What makes mores sense?
As the...
