Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
We're working on getting our nRF52 app working with buttonless OTA updates and the bootloader. OTA works fine with the example bootloader, but when we extend our application...
Hi, I Converted experimental dual bank signed bootloader into single bank signed bootloader and it uploads the new firmware successfully but the problem I got is it erases...
I have an application programed on the nRF 52DK (PCA10040). Its a UART communication to a distance sensor. The Problem is, that I cant send anything from the uC to the Sensor...
Hello,
I just run in following issue. I try to configure an UART to send some bytes. To check the configuration, I just let the program loop, after the sending. Attached...
Hi all! I have a smart beacon kit rev 1, with s110 on it (the latest firmware available). I am using the RTC with the 32 kHz crystal (50ppm) to trigger an ADC conversion every...
After releasing reset to the nRF51, its UART is responding with
RX: A4 1 6F 1 CB
Further requests for things like capabilities, etc go ignored, and opening a working...
hi all,
i cant able to find the version 11 softdevice hex file. can you please send the link.
and can i use the version 8 softdevice for version 11?
-Thanks in adv...
In the migration guide, I can read: "Clearing an interrupt event may not take effect immediately."
And an example of required code is given as:
NRF_TIMER0->EVENTS_COMPARE...
I'm creating a PC application using the ble windows driver by nordic, i cannot implement white list. I ported my code on the firmware & it works.
Is this a limitation of...
When i follow the Getting Started guide for the nRF52 DK at point 5 the led (led 1) does not start pulsating and I do not get contact with my phone. I tried to upload the...
I am trying to make communication between STM32F407ZET6 and NRF52832 chipsets using an SPI interface.
One is master and another is slave. If I take NRF chip as master,...
I am noticing a problem with pstorage_raw_clear when called in the DFU code. My problem is this: when attempting to update an application, if the application is too large...
HI, I have a remote control with nRF24L01. It was talking with Gen1(uses nRF24L01) product via ESB. Now, I am developing Gen2 product*using nRF51822xxaa) and I need to support...
Hi,
i'm doing my own bootloader and i want to use external flash to download image trough a spi. The bootloader project based on example from SDK11, now just an external...
Hello:
It appears (although I am not 100% certain) that there is a small delay (< 10 usecs) between EVENTS_END in the radio and MICSTATUS in the CCM. I believe I have read...
