I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
I have been trying to pair my nRF51822 heart rate monitor device with my Windows 8 laptop. Every time it is unsuccessful and returns the message try add your device again...
Hi
Doing some testing of the nRF24L01+ with LNA PA module, i have noticed noise on the 1.2 GHz frequency, this noise seems to be larger than what is allowed if i was doing...
HI,ALL
with ' nRF51_Series_Reference_manual v3.0.pdf ' , i want to know which pins can i used for adc purpose.
in the sample code.
void adc_config(void)
{
...
Hi there,
The s132 v2.0.0 production softdevice was released recently. How can I use it with the nRF5_SDK_11.0.0-2.alpha? or I have to wait for a new SDK release? When...
I have a bluetooth service which I want to have to initialise a TWI transaction (using app_twi). I want to get the data back from the TWI transaction, but I can't figure quite...
What is the pitch and spacing of the connectors on the underside of the PCA10004 and PCA10005 modules please? Is there a diagram showing dimensions anywhere in the documentation...
@Michael Dietz
Hi Michael!
I am not sure what happened to my last question regarding the BLE example using Segger Embedded Studio. It is no longer visible in the post...
i am already use sdk10 and Eclipse gcc tool chain set-up.. but when i am programming on nrf51822. so, it's not work. also, it's working on nrf51422 QFACAB0(0x0071)..
GIVE...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have the ble_app_hrs example working well with DFU.
When I take main.c from the example code and put it into an RTX project, the DFU stops working.
Symptom: nrfToolbox...
Hi,
I have a python scipt that uses pynrfjprog to program some custom information into a board's flash to be used by my application (calibration parameters, serial number...
I managed to compile the ble_app_uart on windows 8.1 with cygwin. I had to remove all abspath on the makefile, as launchpad gcc is not compatible with cygdrive notation.
...
Hi, I use the NUS most of the time.
(SDK 7.2 & S110 7.1 with IAR 7.1)
As you know, HID keyboard or mouse bond with centrals (smart phones).
After bonding, when using...
nRFgo was unable to read attach to the boards I have with the QFAABB parts, but reported QFAABA parts correctly and programmed them. nRFgo was at 1.21.02.
I updated to...
Hi,
I'd like to retain a value in RAM after any type of reset, including a watchdog timeout, so that I can read it back in the bootloader immediately after a reset.
...
