I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Hi, Nordic Engineer:
Would you like to give me some advice? On my hand, i have a slave ble device(not nrf51822, also i can not change the code). I want to run s120 softdevice...
i am able get the status of led of pca10001 board using usb dongle. now i have to make other pca10001 board as central and want the same data of it? Kindly help, i shall b...
We are planning to optimize the radio-frequency signal,so the some docunments like Simulation model are needed.which can help optimize the RF signal through ADS simulation...
In ble_advertising.c, line 165, you can see such interesting code. I assume it is a copy/paste error:
if(p_advdata->p_tx_power_level != NULL)
{
m_advdata.p_tx_power_level...
For the first, impressed by your intoducing NRF52 chip.
Question: what`s NRF52 indoor range using onboard antenna and maximum output power (+4dBm)?
Thanks.
Hi~
I am struggling to get the BLE packets detected by nrf sniffer (v1.0.1) using wire shark. Its only showing "ADV_IND[Malformed Packet]" periodically. I didn't understand...
I believe what I am asking is extremely specific, but keeping hope that I might get some direction
I have used a clone ST- Link v2 programmer to download code into a NRF51822...
Hi all,
I would like to trigger some actions on difference devices communicating with the ANT protocol based on the distance they are from each other. A simple example...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
Hi all,
First of all thanks for Nordic team for the excellent support. It is very useful for a beginner like me to get started on BLE development.
I am using the nRF51422...
The issue is that if a peripheral needs to enable interrupts (or anything else partly protected by the SoftDevice) and is configured before enabling the SoftDevice, the NVIC_...
Hi, I use nRF24LE1 configured for power down on register retention mode with RFRx active.
When the CPU is on power down i don't have any interrupt from RFIRQ.
Init configuration...
I downloaded the power consumption example code to a nRF51-DK to measure the current consumption during SYSTEM ON and SYSTEM OFF state.
For the SYSTEM ON state, I used...
On our custom board, we have a dedicated hardware reset IC which toggles the nRF51822's nRST line low in response to a magic button press. The nRST line has an external 100k...
Hi,
it's possible to decide if send a scan req to a peripheral device? I want to send a scan req only to the peripherals that have a specific adv packet...it's possible this...
