hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hello,
I am building basic board on nRF5340(based on Raytac MDBT53 module) and after "Erase" operation in nRF Connect Programmer I cannot access chip anymore.
Board...
Hi all,
I am working on Fantel BT40F which uses nrf 5340 soc. I have finished my breadboard testing phase with the development kit and now I am working on Integrated pcb...
Before adding ubxlib module repo into nrf/west.yml, I can build any project with mcuboot with no problem.
However, I cannot build any project with mcuboot after adding the...
Hi,
I'm stuck in the loop of calibration. This is the error that I get from Putty:
It says that I get a TX error.
This is the code that I have for bno055.h:
This...
I used C:\ncs\v2.6.1\zephyr\drivers\adc as an example for testing adc, the following code has been added to nrf9160dk_nrf9160_ns.overlay
I applied voltage to pins p0.13...
I'm trying to test the RGB led on the thingy53.
Using the sample: C:\ncs\v2.6.0\zephyr\samples\basic\rgb_led which gives errors about the devices error: '__device_dts_ord_DT_N_ALIAS_red_pwm_led_P_pwms_IDX_0_PH_ORD...
HI currently i am using nrf52840 s140 sdk ver 17.1.0 and have added buttonless dfu in the central uart application after running we got run time error and we followed the...
Hi,
I am migrating from nRF51 to nRF52810 and I am trying to set Debug because its not working in Keil5.
I use PCA10028 board and I am connecting my beacon to P20 port...
I have a nRF9160DK board that is used for development of a custom nRF9160 board. The hardware designers have assigned GPIO P0.27 to be a general purpose output pin. This pin...
NCS 2.3.0
nrf5340dk_nrf5340_ns -- problem is in non-secure domain for an app built with TFM.
I have this in my nrf5340dk_nrf5340_cpuapp_ns.overlay:
at compile time...
Hi, I'm currently getting familiar with mcuboot and DFU
First of all, thank you very much for the new Academy course that covers DFU!
If I understand correctly, to enter...
I am trying to get MCUBOOT working with project based on the Audio_DK base, where we need to do firmware update over UART/Serial interface.
I have added the following...
I am using nRF5 SDK v17.1.0.
Is it possible to connect a peripheral device by MAC address, and the device is advertising with a different UUID from the central device? ...
I am using LittleFS for an external NAND flash by using the KCONFIG option CONFIG_FILE_SYSTEM_LITTLEFS = y and managing the driver implementation manually. This has worked...
We have difficulties to get RTT prints from MCUBoot while performing DFU.
As far as I understand Segger RTT is reinitialized when booting Application and this might be the...