I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi,
I have new requirements for nRF52832 using the NRF Connect SDK to develop firmware. I want to know how it supports audio playing with the I2S MAX98357. Is there a possibility...
I am working on a pdm microphone using nrfx pdm driver (INMP621) When I am saving the pcm data into .pcm file using sd card and playing the .pcm file in Audacity I am getting...
I'm using nRF52840 with nRF5_SDK_17.1.0_ddde560, using the ble_app_multirole_lesc example file.
When I set extended = 1 in scan_init , the debug session jumps to NRF_BREAKPOINT_COND...
Hi All,
I flashed an nRF5340 DK board with a samples/bluetooth/hci_uart image and one more nRF5340 Audio DK with a samples/bluetooth/peripheral image.
I have not made...
Hi, I am making BLE low power pult, using nrf52811 chip and NRF Connect SDK v2.3.0.
So, the device is sleeping and waiting for button event
When button is pressed, device...
Hi Sir.
customer want to add FEM for nRF7002, target to extend range around 1.5KM.
please check if nRF7002 can support FEM for this application.
Thanks.
Hello,
I'm new to Nordic and I'm currently learning rust on an nRF7002 DK. I know that the LED0 of the nRF7002 connects to the GPIO1.06 of the nRF5340. However, when importing...
Hi Nordic team,
I'm using nRF52832, S132 with nRF5_SDK_17.1.0_ddde560 SDK. I want to send a packet with a notification to my smartphone and then disconnect immediately....
Hi Nordic team,
I'm using nRF52832, S132 with nRF5_SDK_17.1.0_ddde560 SDK. I currently implement BLE peripheral for the NRF52832 as it only healthcare sensor data to the...
Hi
We are using the NCS V2.6.99 for a sample project which scans for peripheral devices.
In this sample project, the scan filter (bt_scan_filter_add(BT_SCAN_FILTER_TYPE_UUID...
Is it possible to route a signal derived from internal clock to an IO pin? I am new to NRF micro controller. My experience has been with Cypress PSOC and in the IDE it was...
Hello,
I have an nrf52833 that interfaces with an external flash module. It is configured to store mcuboot's secondary partition. I am able to write the secondary image...