Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
A problem is experienced with our nRF52840 device, which occasionally stops working and cannot be reset.
Below are the issues observed:
The main software is stopped...
I am working on the broadcast_audio_source example, trying to access audio from the I2S microphone. However, I do not have much experience with Zephyr. The example is mostly...
The thread where it happens is "unknown” despite the fact I name all the threads I create. With addr2line I found that it is zephyr/kernel/timeout.c 56 but it says nothing...
Dear all,
I'm designing a circuit that should allow powering the nRF52840 board with either an USB power supply (USB2) or a (non-rechargeable) CR2032 battery (B1). According...
Hello.
I encountered the following problem. I have an nRF52840 microcontroller that is already soldered onto the PCB board. It doesn't have any bootloader. As an example...
Hi,
We have an nRF9161DK and received our own custom boards this week. When we tried to program our custom board, the development kit disconnected from the computer and...
Hi all!
I'm in the process of trying to put together an nb-iot app on Android studios that would communicate with data from the Thingy 91 board. I've been trying to go through...
Hello everyone,
I've been working on testing PPP support in SLM 2.6.1 without cmux on my Linux host machine. However, I encountered some logs during the process: Note: For...
Environment:
I can't seem to get the one button sample to do anything... I get a steady ~1sec flash from HOST led on the npm1300, but I get nothing from pushing SHPHLD...
I have an EC11 rotary encoder wired to my nRF52840 and I am trying to get readings from it using the sensor API. However, I'm having issues with (seemingly) garbage data....
Good day. We ended up getting a bootloader based on the NRF5 using the Serial Recovery method and a non-upgradable bootloader. The update is coming from a microcontroller...
I'm working on a linux driver for nRF7002 based on the experimental linux driver: https://github.com/NordicPlayground/nrf70-linux-driver . This is being done on linux 5.13...
Is it possible to somehow set a lower charge current than 32mA for the whole charge cycle or force trickle charging for the constant current charge cycle? The issue is that...
I have a GSM application connecting to MQTT that worked previously refuse to work when I picked it up again to improve on it.
To make sure there isnt a problem in my firmware...
The following settings are required to make I2S compatible with the AK5720VT.
MCLK=12.288MHz BICK=1.536MHz LRCK=32kHz Bit length=24bit
CONFIG.RATIO >= 2 * CONFIG.SWIDTH...
