As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hello,
we noticed for one of our boards that the nRF9160 is not able to startup with a floating MISO pin on the SPI where the flash is configured in device tree (SPI1 /...
We have a custom board based on the nRF52805 that does not have a LFXO, instead relying on the RC. We are using NCS 2.6.1.
We see current spikes every 4 and 8 seconds that...
Hi,
as mentioned in the title, when using the official vscode extension (nRF Connect for VS Code) for debugging and stopping a debug session, the target state does not get...
Hi：
I have the following hardware structure：
FPGA < -- SPI -- > NRF5340 (TX) -- ! ( ESB ) ! -- NRF5340 (RX) < -- USB -- > PC
Due to the nature of my application, I need...
Hello!
I am trying to collect data from an nRF52832 device which works as a peripheral to another device nRF52832 which operates as both Central and Peripheral.
Description...
Hi,
I am downloading GPS Almanacs from U.S. Coast Guard Navigation Center web site to inject into the modem using nrf_modem_gnss_agps_write() . Below is current almanac...
Hello,
I need a way to decide on which Api to use for UARTE (configured as uart1) once in main(). I am not intending to switch between them nor to use them at the same...
I am currently working on a project to migrate to the nRF Connect SDK. We are using the NRF52840-CKAA-R7 package of the nRF52840. However, I have not been able to locate the...
I'm develping application on nrf52832 with nrf5SDK v17.0.
The connection interval is set to 12 to 16.And the conn_sup_timeout is set to 1000.
The condition happened frequently...
As I understand it, any applications using the modem libraries on the nRF9160 must be built in the non-secure domain. The MCUboot and TF-M needs to be in the secure domain...
Hi.
I need read the external voltage in input P030, and the battery backup voltage in P031.
If I read using only one channel, the P030 (AIN6 ) the value that show...
I want to send key strokes between two pic 16f887 microprocessors using the nRF24L01. I assume I can use ShockBurst to do the job. The master sends the key strokes and the...
Hello,
In the nrf5340_aduio application. I found it support 2 channels both of output(mic signal) and input(audio signal) on the USB device.
But i want to know if it can...
Hi,
I am debugging an application whth MPSL enabled and occasionally get this error:
E: SoftDevice Controller ASSERT: 48, 190
E: ***** HARD FAULT ***** E: Fault escalation...
Dear Nordic team,
I'm evaluating nRF5340 Audio DK for the use-case of broadcasting multiple streams.
Until now I've succeeded in broadcasting 4 streams (LC4 bitrate...
