Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
Hi,
We have been using SDK version 2.1.1 and currently are in the process of migrating to SDK version 2.5.0.
Would be helpful to get some hint regarding what conditions...
I am facing issue with BLE advertisement in nRF52833. The board I am using is rayBeacon : nRF52 on-the-go Development Kit. The code I am using is example code from nRF Academy...
I am trying to write and code of aes encryption and decryption using ccm mode for my application on nrf52832 controller. I have went through some example on Github for the...
I am developing UARTE using nRF52840.I use a wire to connect the TX and RX pins together, and send something out the TX.
However, RX did not receive any data, and the interrupt...
Hi,
I have the separate working codes for the TWI0 and the SPI1. However, when I combine them, it doesn't work: sometimes it takes forever waiting for the NRF_DRV_TWI_EVT_DONE...
Hello, I'm trying to figure out how to work correctly with timer 0 in the nRF24LE1 microcontroller.
1)The Cclk frequency in my case is 16 MHz
2)Given a fixed limit of...
We are new to Nordic and have been making great progress with our nrf52840DK board and successfully running many of the Nordic SDK examples. We can't seem to find a single...
hi
the saw filter used in thingy:91 is : SAFFB2G45MA0F0A which is obsolete end of life now
suggest me another saw filter for ble application chip antenna implementations...
Hi all. I am using nRF5 SDK 15.0.0 and the S140 SoftDevice v6.0.0 to develop on an nRF52840. Due to software infrastructure constraints, I am unable to implement DFU using...
Hello,
I have a use case where I need to use UART_RTS and UART_CTS as GPIO for toggling the led. I also want to use the other two pins UART_TX and UART_RX for handling UART...
I have created an application that initiates a timer for 30 seconds and when it expires it calls an expiry function that switches the system off, if no button is pressed since...
If you try to write a program on a board with nRF5340 installed, an error will occur.
I can write to other boards using the same J-Link, so I don't think it's a J-Link problem...
Hello all,
I have scoured the devzone and other blogspots to find an answer to this but so far have come up short.
in short i want to use one NRF552-DK with the adafruit...
Hi,
I made DFU procedure with a distributor (nRF52840 DK) and one target (nRF52840 dongle): procedure completed successfully in approximately 45min
Then I made DFU procedure...
Hello,
I have a problem with a custom board with a nRF9161. I am trying to connect the board with the nRF9161 to the LTE or NBIOT network, and the board doesn't seem to...
