As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hello,
I have a use case where I need to use UART_RTS and UART_CTS as GPIO for toggling the led. I also want to use the other two pins UART_TX and UART_RX for handling UART...
I have created an application that initiates a timer for 30 seconds and when it expires it calls an expiry function that switches the system off, if no button is pressed since...
If you try to write a program on a board with nRF5340 installed, an error will occur.
I can write to other boards using the same J-Link, so I don't think it's a J-Link problem...
Hello all,
I have scoured the devzone and other blogspots to find an answer to this but so far have come up short.
in short i want to use one NRF552-DK with the adafruit...
Hi,
I made DFU procedure with a distributor (nRF52840 DK) and one target (nRF52840 dongle): procedure completed successfully in approximately 45min
Then I made DFU procedure...
Hello,
I have a problem with a custom board with a nRF9161. I am trying to connect the board with the nRF9161 to the LTE or NBIOT network, and the board doesn't seem to...
Hi,
We've got a board with a fairly limited power supply in production and it's expected to brown out under certain conditions. As such, I need to verify the reset loop...
Hi community,
ncs-2.6.0 I'm using.
I'm trying to enable bmi270 as I enabled adxl362(is already working), both are connected with SPI.
but it shows me this kind of...
In my project I use MPSL for a combination of BLE, ESB and flash sync. The BLE/ESB timeslot handling was implemented following this example: https://github.com/too1/ncs-esb...
Where to find the sample for nrf5340 net core that is written by default. I mean when I use BLE observer sample with zephyr controller there is some code that goes in Net...
Does mcumgr support relay functionality? On one device, I have a firmware image stored in external flash connected to a 9160 and need to relay that image via UART to an on...
In case of peripheral losing keys, but client(Android nrf connect app) still has them. ( shows it is in 'Disconnected + 'Bonded' )
On the next connection attempt, there...
Hi,
I'm trying to build my custom test project with the nRF Docker in accordance with https://github.com/NordicPlayground/nrf-docker .
I've started with this simple script...
I am a BLE beginner and have some confusion about the IQ data of Bluetooth AOA. I used the example direction_finding_connectionless_rx and direction_finding_connectionless_tx...
