dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi,
I have implemented a set of custom mesh models on nCS. In vendor models we have reset handlers, as in nrf documentation: https://developer.nordicsemi.com/nRF_Connect_SDK...
Hello,
We cant get a connection to our Matter Development Board like in the discription: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/connected-home-over...
This may just be more of a Zephyr question but wondering if anyone in the Nordic community has experience with this.
I'd like to generate code coverage reports when running...
Hi,
I'm developing a board based on the thingy91 (same nordic silicon, different sensors) and using nrf SDK v2.0.0
The blinky application is flashed and run correctly...
Hello, I am using the nRF connect SDK and am currently running into some issues with using the on board ADC. My issue relates to the adc_channel_setup function which returns...
Hello,
I am using an nRF52833 dev kit and the Zigbee light_switch example from nRF Connect SDK.
I was trying to implement the sleep mode so I wanted to estimate the power...
Hello,
I am having an issue with board bring up for a custom board I developed using the nrf5340 processor.
I have created firmware based off the peripheral_uart sample...
Dear Nordic support team,
I bought 3 piece of nRF52-DK from MOUSER, 1 piece of nRF52-DK version is 2.1.0 , and another 2 piece version is 3.0.0.
nRF52-DK version 2.1...
Hi there,
We're using nRF52840, IAR 8.40.1, nRF5_SDK_16.0.0_98a08e2. My question is, I need to toggle a GPIO pin right after SPI finishes the TX transaction and right before...
I am trying to use both USB and BLE on an NRF52840 using SDK 15. It hit a hard fault during initialization, specifically when it tries to enable the USBD IRQ.
It looks like...
I am familiar with the PTCRB certification process for an IoT device incorporating a certified module. https://www.ptcrb.com/wp-content/uploads/2020/08/10_Steps_to_PTCRB_Cert_for_Cell_Enabled_IoT_Devices...
Hi, all
How to enable and set fast advertising and slow advertising in NCS.
We always set advertising parameters in legacy SDK like below, how to implement it when using...
Hello All,
Thank you for reading my post. I have finished developing a small battery powered device I have been working on and just completed programming the functionality...
Hardware: nRF52840dk
SDK: NCS v2.0.0
application:
Calling bt_encrypt_be() during OpenThread network traffic hangs the device when using MPSL with OpenThread 1.2. ...
Hello everyone,
I'd like to build a Relay Node in Light Switch Example but I don't know how to implement firmware.
Can you support this for me? Thank you so much.
...
