I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hello,
I am writing the device tree for our custom board, which uses an nRF9160 SiP. This approach to configuring the hardware
is new to me, since my experience is with...
Hello,
We are attempting to track down a rare bug in our code that causes the device to occasionally hard fault.
We have been able to catch it three times, twice where...
Hi,
When I connect nRF52833-DK device to the (Windows 10) system, its JLink UART (COM) Port disappears after some time (in about 4 to 5 minutes.) The following screenshot...
hello Nordic
i work with nrf52840 , .. want to move to ncs 1.8
seems that moving to ncs 1.8 forces me to update to zephyr-sdk-0.13.2 (from 0.12.4)
is it really a must...
Hello,
I have added the line CONFIG_DEBUG_PORT_ACCESS=y in prj.conf file and now the project does not open in Segger Embedded Studio (SES).
I am getting this error,
...
Hi,
I am building my Project in an out-of-tree form and up to this point I solely used Segger Embedded Studio to compile our project. I am using a custom board with an nrf9160...
Hi All!
I am using VS CODE studio as an IDE for nrf9160 FW development. Blinky app compiled and work perfectly. But when I compiled the asset tracker/cloud client it gives...
In my code, the parameter definitions like this :
In my application, I used SAADC in SEGGER to convert my analog sensor input to digital and then i want to sent...
I just updated the programmer tool in NRF Connect 3.10.0 to the new version v2.3.0.
Now I'm getting this error: unrecoverable error.
Restore default settings did not help...
Hi,
I want to know if its possible to add multiple services and characteristics to several BLE central devices (based on nRF52) which need to communicate to a single peripheral...
Hi,
We are currently looking into using the nrf9160 for a smart meter gateway like solution. It is of particular interest to us to know if we would be able to achieve compliance...
Hi all,
I am having issues with the nRF connect programmer that is used to flash the mcu.
I have installed the software my nRF connect version is v 3.10.0 (It is not available...
I installed nRF Connect and inside it I installed Programmer. When opening the programmer I get the following exception:
And system report:
I already tried following...
