Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hello All,
Method 1: I am writing a test application to read the ADC data at a specific intervals(10 samples for every 5ms interval for every 50sec). I am using blocking...
Hi,
We are implementing a synchronous light flashing of multiple devices, so:
1) Can we get a millisecond level (< 10ms) time synchronization by parsing the Link Layer...
Hi, all
I added a scanning module to the example 'ble_app_uart.c', so each one works well.
What I want to do is advertising and connect at the same time while connected...
What is the best practise for multichannel SAADC conversion in ultra low power devices? For example I have to measured 4 channel in interval 250ms. Below what I try:
...
Hi, Dear Nordic & all:
when I run the ble_app_hids_keyboard example in nrf52820(SDK17.0.2), I meet a question:
1、Frist I use my iphone connect ble device and pair success...
Dear Nordic:
so I want to know In nRF52 serials chips, How much HFCLK CONTROLLER ppm is the frequency offset distribution and production FT control range? Do you have any...
Dear all, now I am making a data sampling system with multi peripherals and one central. The peripherals sample data from sensor via SPI port and transmit data to the central...
Any SSD1306 example for nrf51822 ??? I found this but is for nrf52.. i try to add it for my nrf51822 but there are tons of functions with different declarations in my sdk...
I have nRF5340dk board and my question is that can I use only networking processor to run the BLE applications? If not why? As the Radio hardware is only connected to networking...
Hello , I want to read analog values from potentiometer using analog pin P0.04 (A0) on nrf5340 with zephyr ecosystem . Where can I get beginner documentation like setting...
Hi,
I'm a beginner, and currently working to implement a low-power controller using nRF52-DK and Power Profiler Kit (PPK).
I ran the following codes (system off) and expected...
I have setup a 1-1 paired central(+peripheral) <=> peripheral Central is a 52832, SDK 16.0, SD s132 v7.0.1 peripheral is a 52811, SDK 16.0, SD s112 v7.0.1 My code is based...
in this example
/root/ncs/nrf/applications/serial_lte_modem
I want to build_nrf9160dk_nrf9160 in secure mode
but compile error #ifndef CONFIG_TRUSTED_EXECUTION_NONSECURE...
Hello,
I am confused on which plateform I should use to program my nrf52832 chip.
First it is advertised to use Segger Embedded Studio that I am trying to configure...
Hi all. I am using Keil for programming a nrf51822 & SDK 12.3 I want to use the SSD1306 OLED Drivers in my project I follow these steps: 1) I copy .c and .h files form github...
