Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
If I use zb_zdo_mgmt_lqi_req() for dst_addr = local short address is the response resolved internally?
I have an application where I need to locate certain zigbee devices...
nRF Connect 5.0 crashes after asking to install nrf-device-lib-driver-installer.exe and shows the following cryptic message.
Trying with nrfconnect-setup-4.4.1-x64 raises...
HI all!
I've been doing some research on working with nRF Cloud and I have a few questions/clarifications:
1. In general are you able to drive/control a GPIO pin through...
Hello
I have a project, where I need to have NUS-BLE with firmware update functionality and openthread.
BLE and NUS config:
FOTA config is:
Thread config is: ...
I'm struggling with SDKConnect and the device tree stuff... and finding it hard to get good examples or docs TBH
So, I have the sample dts files for the nRF5340DK, which...
Hello, I have a problem with the bluetooth connection to a Samsung s21. It connects for like two seconds and then disconnects immediately. Then tries to establish a new connection...
In build configuration i need to select nordic board . i have been using fanstel bt840 use nRF52840 QIAA, ARM Cortex M4F, 64 MHz . what board i have to select in this ? or...
Hi, we're having some problems and need help. We have a usage scenario: in HOST mode, the switching rate is 250k/2M every 10ms, the time slots of the two rates are different...
Hi I am trying to interface QSPI with NRF5340 dk board. I am getting build errors. I have used SPI-FLASH sample and it was working fine and I am trying to change the SPI-FLASH...
Hi,
in the new version of nrfx there is a function (nrfx _uarte _rx _new _data _check ( &uarte _instance ) , and how to get a similar result for the older version of nrfx...
Hi,
I have been testing the CAF click detector module and I find that any event callback after the click event takes almost 1000ms. That is the time between the actual click...
We are working on a project, with a working secure buttonless bootloader that works flawlessly. However I recently made it with bonds, and it works with all of the devices...
I'm experimenting with the Bluetooth Throughput sample in NCS v2.6.1. As I increase the distances between devices, I see strange gaps in the transmission from the Central...
Hello, when testing the BLE sniffer with an nRF52840 dongle (utilizing the most recent official sniffer firmware), I configured Wireshark to capture the coded PHY. After initiating...
Hi,
We are working on integrating nRF-Mesh-Library (iOS and Android) sdk into our app for mesh networking, it should support identifynode, provision, add app key and add...