Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode,and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello, I have developed a program that reads (with I2C) a temperature sensor and sends it to the central board. The central board is a NRF52480-DK. I have tested the peripheral...
Dear Sir.
I was testing dfu mode with an nrf52840 dk and held down the IF BOOT/RESET button, then powered up and waited a few seconds before it went into bootloader mode...
Hi,
I'm evaluating the NRF52832 for an ultra low power BLE application where I'm going to use GATT. I've built some prototypes with the NRF52832 and right now I have to...
Our engineers have two questions that they are confused with:
1) When applaying ble techniques, does nodic 52 serious of chip compatible with SIG mesh?
2) When applaying...
Hi there,
we are working on getting type approval certification, and the test lab is asking for fixed frequency software, drivers and SOP.
What we need is the fixed frequency...
Hi,
The actual problem: I want to store some stuff to flash at factory, that is never erased. And I also need another persistent memory that can be written in runtime. I...
Hello I am now trying to implement an active NFC Tag using nRF52832. But I don't know what that example project is. Can you point to a command or example source that performs...
Hi,
nrf-sdk: 1.3
Firmware: 1.2.1
Using offloaded sockets(secrets at the modem side)
My use-case is this: Provision PSK and identity to device at the factory for DTLS...
Hello,
do you have any method, example or other documentation to recommend to me in view of implementing the storage into non-volatile data with our thingy91 ?
we use...
Hi team,
Is it possible to route the low frequency clock inside the nRF9160 to an external device? If not, then the only option is to generate the clock using the timer...
Hi,
We use the nRF radio timeslot API to take control over the radio and other peripherals periodically. We have noticed that when the timeslot is active (we own the peripherals...
I tried to use the Bosch BSEC library for the Asset Tracker application for nRF9160.
It seems that the Asset Tracker was build for BSEC 1.4.7.4 which is unfortunately no...
I develop a test fixture based on nrf51 code that I use for final product.
NRF51 is just a part of a complex test fixture, then I have just "one" test fixture model.
I...
Does m_xfer_done need to be set to false before calling nrf_drv_twi_rx? If so, does while (m_xfer_done == false); loop need to be called on every read?