Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi, Please have a look and let me know about it.
This board is two layers and i used chip antenna. I would like to ask you, Is this design is correct? How can i plan with...
I have an ongoing issue with using the Keil compiler and the supplied examples.
There has been some email correspondence which is detailed below:-
Hi David,
I have...
Hi
I am reading the sensor data (Irms and Vrms) via I2C protocol and multiplying the read data with 0.000030517578125 to get correct result but i am getting the result as...
Hi:
I use nRF5_SDK_16.0.0_98a08e2\examples\peripheral\usbd_ble_uart_freertos.Error:Unknown USB device (device descriptor request failed).
I use nRF5_SDK_15.2.0_9412b96...
I'm trying to add a SPI driver to the ble_app_uart_c example. For now, I'm just trying to make this driver shoot out a SPI transaction every time I click a button on the dev...
Hi,
I am trying the freertos on my project with nrf52840, sdk14.00, s140_nrf52840_5.0.0-2.alpha_softdevice.
As i can see, there were no example codes for 52840 in the...
hi
I`m debugging the nrf52840 on the pcb I made and have some problem
I know Reset pin is P0.18 of nrf52840 but 3.3V was not measured. So the reset pin does not work....
As mentioned in this article are these vulnerabilities addressed in Nordic Semiconductor's products?
https://thehackernews.com/2020/02/hacking-bluetooth-vulnerabilities...
Hi everyone,
I am using the nRF52840 and SDK 16. Following THIS tutorial was able to create my BLE custom service and see my service with the custom UUID.
The problem...
Need to design a simle RSSI based tracker using nrF52810. Due to current global issue, cannot order hardware at the moment.
So meantime I am planning to learn all software...
Hello,
Originally, the Zigbee light_control examples ships with a bulb that can call the zb_bdb_finding_binding_target() function , and a light switch that calls zb_bdb_finding_binding_initiator...
I searched in this forum about softdevice_fault_handler errors, but could not find the cause of my problem. I need to obtain more information for a softdevice_fault_handler...
Hi,
Can you please let know a way to run two processes two process simultaneously on the two cores of nRF5340 board. An example project would be of great help !
Thanks...
