Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hello Everyone,
I'm involved in a project where we are evaluating ble mesh and Thread mesh on nrf52840.
I want to know, does Nordic supports ble mesh and Thread mesh simultaneously...
When using Keil Compiler, I am unable to compile any of the ble_peripheral examples. I get an error that says...
RTE\Device\nRF52832_xxAA\system_nrf52.c(29): error: #5...
Issue with NRF52832 Firmware installation
Hi We are developing custom boards with nrf52832 chip, and it is working well.
The issues occurs when installing firmware without...
Hi,
as i mention in https://devzone.nordicsemi.com/f/nordic-q-a/44924/dfu-serial-failed i have f ramming error now and then when i do DFU over serial.
My idea was to write...
Hi,
after I received the thingy91 I wanted to connect it to the cloud, as mentioned in the get started.
But when I want to add the LTE Device, it shows the following Error...
Hi,
I got a new USB840M that have only the NRF52840 with a USB connector, I installed the nordic_cdc_acm.inf (driver for USB) for my PC, and my PC started to recognize...
Hello
I'm using the Development kit nRF52840, SDK 15.3.0, and the Sofdevice s140 6.1.1
I've created a BLE Battery client service, my implementation is extended upon the...
Hi Nordic DevZone,
I am currently trying to implement a system whereby a nordic nRF52 board scans and broadcasts in alternation, using freeRTOS tasks.
I have yet to...
When I tried building the Mesh 3.2.0 SDK on MacOS with cmake, I got link errors with the static libraries rtt and uECC.
The fix I discovered was to change the CMakeLists...
I am working on developing an application where the app layer tries to throw out messages if the message parameters are not valid. One the parameters to validate is a TID...
Hello, I working for TSS.se now selling 100.000 temperature-loggers annually. We aim to develop a new IoT based logger based on nRF52832 as a replacement.
Does following...
In order to compile against custom hardware, we changed overlay and dts files, but I cannot remember which. How do I find out?
I get the error
devicetree error: 'ss-pin...
I am using NRF52832 as Beacon, I want to classify the RSSI as High, Medium, Low, and Poor based on RSSI.
I am using SDK14.2.0 for Beacon and Gateway.
And using +4dBm Tx...
