Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hello,
I am using Segger Embedded Studio to run AWS FreeRTOS bootloader demo on the nRF52840. When I try to build, I get the error cc310_bl_backend_ecc.h: No such file or...
the first (initialized) Eddystone (e)TLM frame have vbatt unset. I am using SDK 15.3. I suggest the following changes, it simply busy wait until ADC reading is finished before...
I had been programming custom boards with the nRF52840 DK both through nRF Connect and the Command Line tool without issues. I have shorted SB47 to provide power to the target...
Hello,
I am see odd behavior with SES and git repos. I was working on a branch and wanted to confirm there was no issues with the building the project before I started adding...
I am sorry to ask a stupid question as i supposed to fix firmware issue with my zero knowledge.
Before android app (central) connected to peripheral ble 52832, If I press...
Hello,
We have developed a GATT based application based on nRF5_SDK_15.0 (Bluetooth LE without mesh). We want to add mesh functionality in this code as you described in...
Hi, I am new to Nordic devices. I have purchased Nordic Thingy91 (PCA20035).
I need a small clarification on the programming/flashing the nRF9160 and nRF52840 on Thnigy91...
Hello
I am trying to operate the ble_peripheral_hrs example found at SDK 5.11 (several years ago) for Segger, but I can't found a project (*.emproj) for it.
Have you know...
Hi,
I have nrf52840 on my custom board (Based on IMX6, Running Yocto linux) which is connected over UART.
I want to an OTA of zephyr OS on that chip over serial and for...
We have a custom device that we profile with a PowerProfiler (external DUT). Device is battery powered.
We have a strange idle current: cca 5 uA for 2 min, then 900 uA ...
Hello,
I am new to the nrf9160. i am quite confused in between nRF Thingy91(pca20035) and nRF9160DK (pca10090) .
What are the steps i need to follow to get start with...
Hello:
I want to change uart0 tx and rx pin from default 28 and 29 to 10 and 11.
I know the i2c pin change need to change nrf9160_pca10090ns.overlay in app.
So I tried...
For quite a while I've noticed that across multiple custom boards using the nRF52 I've been seeing low-level current spikes from a part that is in SYSTEM_OFF mode. They are...
i got 'LIS2DH12_ADDR' undeclared (first use in this function) error when i build my project but i already define it in pca20020.h file.
this image is i define about...
