I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hi,
I hdd developed a ble product based on nRF52810 ( SDK_15.3.0_59ac345 s112 ). I had set the connect paramter like this:
MIN_CONN_INTERVAL MSEC_TO_UNITS(150, UNIT_1_25_MS...
Hi,
Do you have a better example than the one on nRF Cloud that can show me how to transform a HTTP GET /message from my thingy. Right now, the messages are nested and it...
While I know the 9160 does not support voice calls, I would like to know if the 9160 will accept mobile terminated (MT) data calls. If so, how is that represented in the firmware...
First of all , p lease forgive me for m y bad English if it annoys you .
I do have an interest in nRF52840 development kit, because I am trying to find a development kit...
After updating from THREAD SDK 2.0 to SDK 3.1 I am getting NRF_ERROR_NO_MEM in nrf_sdh.c.
The project is based from the multiprotocol BLE thread dynamic example.
The code...
I'm creating a ble central device that receives instructions via UART on which device to connect to and which UUID to write to.
I'm able to connect to a peripheral device...
Hi,
I am working with NRF52840 and want to encrypt my saved data with AES using CC310 cryptocell.
I am working with nrf_crypto_aes frontend to do AES.
I want to know...
Hello,
I'm trying to build and run 'secure_bootloader/pca10040_ble_debug/armgcc/' example and it seams that it stops with some hard fault:
Remote debugging using localhost...
Hi,
I tried to evaluate the light switch demo using the boards that I have to my disposal.
These are 1 nrf52-DK and 2 nrf52840 Dongles.
I wanted to use one dongle...
in application design , this pin is not connected to VDD , but application board works well ,
application's power range is 2.2V - 3.3V (AAA batteries), max current consumption...
I'm attempting to troubleshoot why my HM18 doesn't connect to the ESP32 over BLE. I'm now deep in the rabbit hole that is BLE sniffing so now I'm trying to determine if the...
Hello,
I did a side by side comparison of the latest nrfutil v6.0.0a0 vs v5.2. It looks like v6.0.0a0 is much slower.
Looking at the log from the target device, it looks...
Hi,
I have installed Embedded Studio for ARM v4.22. However, the studio crashes when I select 'Activate Your Free License'. Reinstalling does not help, and neither a different...
Hi,
In order to read values from TH02 sensor(Address: 0x40) I first need to give a command i.e. write 0x01(for temperature) and 0x11(for RH) resp into internal CONFIG register...
