Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I am using a custom board with the nrf52832 with SDK 13 and I have a bootloader and an application that both configure and feed the WDT.
However, upon restart (power...
Is there any straight forward way to detect jamming using any technique on this Nordic device? I'm using SDK 15.2, Soft-Device 6.1 Would this be possible by the new SD 6 function...
I have been using SMD modules with NRF24L01+ fitted.
The first batch I used worked fine for months.
Then I purchased another batch and found the tx_ds_active or max_rt_active...
Hi,
1. I went through the document. I'm trying the example applications Light-Switch on PCA10040 DK and NRF5 SDK for Mesh V2.2.0. So it is like the Client will be provisioned...
Good afternoon,
Following up my previous case, to which I got no reply, how can I use a queued write characteristic to write less than 20 bytes of data?
I'm using it...
I'm trying out Zephyr on the nRF52 DK, specifically I want to test the ADC drivers. Since things are moving quite fast in the Zephyr development world, there may be some information...
Hello, I'm working on Mesh SDK 2.1.1 and I'm trying to send a Relay Set message through Configuration Client. I have changed the code of models_init_cb() function inside the...
The nrfx_spim driver has an issue when chip select pin of the driver is not used.
When nrfx_spim_init is called with a nrfx_spim_config_t whose ss_pin is set to NRFX_SPIM_PIN_NOT_USED...
Dear Nordic
I have custom board(nRF52840) its not detecting through Jlink (from nRF52 DK).
I tried to connect nRF52840 dongle(using J2 in dongle) with same setup its detected...
Hi,
I am latest SDK 15.0, and using FDS library to store custom data. I have followed FDS examples but couldn't succeed in writing data to flash. When i tried to debug,...
Hi Guys,
We started to develop a mesh network with nRF52840 DK's and dongles. I have made some adjustments in the code with segger to use the server example of the led switch...
I just want to globally set the power level, and forget about it.
I have seen this post, and it still seems unclear how to do this - or if it's even possible.
Is there...
Good afternoon,
I had a question regarding scanning and pairing. Is it possible for a peripheral device to send scan requests after its been paired? or does the device have...
update SD+BL+APP from sdk12.2.0 to sdk14.2.0 , hang at trying to reconnect after loading the 1st image out of 2 on NRF52832. need reboot iphone and DFU application only to...
