I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi,
After successfully managing to preserve our devices bonding information (and custom app context data) across DFU updates, we have a few related questions.
I should...
I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I run the "ble_app_uart" from sample program and leave it as it is. The program ends in NRF_BREAKPOINT_COND with "Fatal error" after a while. It is displayed as a screen...
Hello
I am using the nRF52832 with SDK 14.2, JLinkRTT Client, and SEGGER IDE. The system simultaneously runs a soft DAC, IMU, digital potentiometer, and provides variable...
Hi all!
I want to use the BLE stack by Nordic. I figured out that S132 is the appropriate HEX image for nRF52832. I can burn the softdevice into flash with nrjftool.
An...
We have an application where certain executions hold more priority over BLE link. We are implementing a critical section(disable/enable interrupts). However, in some corner...
Hello I've noted some problems when try to use the app_timer in repeat mode with a tick time <= 100ms. I see that the BLE Mesh SDK sets the RTC1.CC[0] compare register in...
I my application, I wish to send a large (60 bytes) bulk of data atomically, i.e. either send all or nothing. Assume I cannot increase the MTU.
Is it possible to query...
Hi
I am using the SDK 15.2.0 and developing for a NRF52832 using Segger.
I have a problem with the define NRF_SAADC_CHANNEL_COUNT in "nrf_saadc.h". It is set to 8. ...
Based on Mesh SDK 2.1.1.
I use light switch proxy client & proxy server to test server publish function.
But when I use the phone setting network, I found that the client...
Dear nordic,
we build a custom board with nrf52840. Now i face some issue i can't flash the board. when i start flashing its show some warning reset pin is high.
I...
Hi,
I just want to verify-
The MAC address of the bootloader is the app MAC address +1, assuming we are using the default configuration.
Is that correct?
Thanks, ...
Hi Support team,
The Online Power Profiler is calculating the Average Current consumption for nRF52840 DK board in a wrong way.
Calculation is of blocks. => Pre-processing...
Hello
I would like to integrate DFU into my application
but, when including:
#ifdef BLE_DFU_APP_SUPPORT #include "ble_dfu.h" #include "dfu_app_handler.h" #endif...
Dear NRF Team:
I successfully updated the firmware (blinky_nrf52840_xxAA_s140_6.1.0) according to the Mesh DFU steps.
However, the second DFU cannot be performed after...
