I'm looking for a good firmware engineer that can take my current firmware and add the buttonless DFU to it. I currently use the Keil environment but am open to switching...
I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
I know this question has been asked before, but I couldn't find an answer...
I'm looking for an example of how to use the nRF52832's SWO feature with the SEGGER JLink product...
Hi. I am using nrf52832 SoC with s132 device (4.0.2). Device is acting as peripheral, I have set max BLE connection limit to 1. ble_cfg.gap_cfg.role_count_cfg.periph_role_count...
I'm following the migration guide from SDK 14.2 to SDK 15 , and am a little hung up on the new nRFx module.
All the examples in the new SDK use the legacy drivers but the...
I'm using the CR2032 to power up my nrf51822 with LDO setup, it works well in the begining. But when the voltage drops below 2.6V, my phone cannot scan the BLE. Is it little...
What is expected behaviour of s132 device (4.0.2) if peripheral is initialized with periph_role_count=1 and somebody tries to connect when BLE connection is already establsihed...
Hey Guys,
I'm a newbie on BLE development , I'm trying to run the example "examples\ble_peripheral\ble_app_ancs_c" , It works well first time, but it cannot receive the...
I'm using nrf52832 powerd by a 3.6V regulator in a li-ion powered application. And using one of the IOs (P0.05) as the power supply of other circuits.At the same time, using...
Hi
I am having trouble getting the basic BLE_APP_UART up and running. The UART printf() works, but the BLE module (NORDIC_UART) is not visible in all the devices android...
hi,
i am doing a project where i am using central and client model.
i am using nrf52840 as central device and thingy 52 as peripheral device and i am using sdk 14.2.0...
When using make flash on an SDK11 sketch, s132, pca10040, on Ubuntu 18.04, it successfully builds everything until app_uart.c; when it gets to that point, it outputs the following...
Hello,
I would like to test my code on a NRF52832-QFAB chip with 256kB chip to see whether my code fits into the 256kB flash variant.
According to nRF52832 Rev 1 Errata...
hello
i am using segger embedded studio. with nrf52840 and sdk15.
i was working to set the clock using nrf_clock_lf_cfg_t which is defined in nrf_sdm.h .
nrf_sdm.h is...
Dear Sir/Madam,
I am working on a 51822 project which send data to Android App. This project is actually an replacement to an old BLE sensor which is obsolete now. I have...
HI.
I use the peripheral example of SDK15 to implement functions such as uart, spi, and interrupt.
However, if soft device S140 is programmed, then my code is not programmed...
