Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
Hi All,
Can one safely assume when sending a packet to a destination address using the ping command in the CLI, that the payload echoed back is the payload transmitted...
mainc.txt
we can use INTENSET to enable certain events on the radio as in line 460 in mainc file attached. But how to enable this on the radio as a whole.
I basically...
Hi Nordic,
I am trying to enable the DC/DC converter on a QFAAH10 (revision 3) .
I am using the s130 v2.0.1 SD .
----------
1. sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE...
Hi,
If I configure the radio notification to ACTIVE and then set a DISTANCE of 800us, is there any way that I can configure PPI to toggle a pin for example?
I know that...
We are applying the CE certifcate for a product using nRF51822 and softdevice S130. Certification lab requires us to fill in below techanical questions. Please help to answer...
Hello, my program stuck at these assembly codes:
I decided that it was stuck because I keep pressing F11 and it just go around in circles in these 4 lines.
So:
...
Can't I connect to device that hasn't been discovered yet??
I'm trying to connect one device( A ) to another device( B ) which ADDRESS is known but never discovered yet...
Hi there,
We're looking at doing something with beacons so that we can make use of the way iOS handles scans for them in the background differently to other peripherals...
The debugger does not work with the latest GNU toolchain for ARM Cortex-M build. It throws the following error on Eclipse:
Could not determine GDB version after sending...
GPIOTE Library makes my Board(nRF51422-QFAC) Brick??
I just build my nRF51422 Board, and It's pretty working well before I've used GPIOTE Library.
Before using GPIOTE...
Hi everyone,
I am seeing an issue where the SPI (master) ignores the first byte of RX buff and begins storing the received bytes from RxBuff[1] instead of RxBuff[0]. In...
Does anyone know if there is any documentation of nrf51822's current consumption? Perhaps, something similar to CC254x's Application Note . I'm mostly interested in the current...
Hello,
I would like to build two boards that can send small messages between them, at long distance. For that I would like to use some of your devices (I used 51822 in...
Hi
I have working module which communicates via uart with another module. It works good, unless it is heated to 40C. After that temperature UART communication is not correct...
