Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi,
we have nRF54H20DK (SoC rev. "C"). connected to MAX77655 via I2C (SCL ~ P1.0, SDA ~ P1.4 according to I2C restriction).
I am trying to test i2c131 for reading/writing...
Hello,
We are using DFU target library with MCUboot (Connect SDK v2.9.0):
And we are getting assertion fail on first dfu_target_offset_get() call after FW update:
...
Please confirm whether the "sample app nrf5340_audio" in "v2.8.0" supports "GAIN control" in "SPI+GPIO mode". the method to enable "GAIN control" in "SPI+GPIO mode" if the...
Hi Nrodic，
Does NRF5340 have an example code for QSPI driving uLED display peripherals (for example, I need to drive this display chip: JBD013VGA， As per the attached...
I'm following along with the Nordic Academy tutorial for v2.7.0-v2.9.0. I made the recommended modifications to my v2.9.0 project with an nRF54L15-DK target:
Create sysbuild...
Hello! I am developing my own BLE solution where I have the different attributes in my service and I am connecting two different nrf52840, one to act as a GATTClient and one...
I am attempting to do a simple read from the FEM on the nrf21540-DK board. I should be able to use the zephyr driver with spi3 (or fem_spi) to do a simple read/write from...
I'm writing a client/central application connecting to a peripheral, discovering a service, and then wishing to enable notifications from a specific characteristic.
Once...
Hi,
I am trying to write a file to the FAT file system on nRF7002 board.
Here is what I have tried:
in proj.conf:
ONFIG_FILE_SYSTEM =y
CONFIG_FLASH =y
CONFIG_FLASH_MAP...
Hi,
we have nRF54L15DK (rev. 0.9.1). connected to MAX77655 via I2C.
I am trying to test i2c21 and i2c22 for writing data. I have tested it on different SCK and SDA on...
I'm following the instructions to build a co-processor using the nRF52840 dongle, on Ubuntu 22.04: https://docs.nordicsemi.com/bundle/ncs-2.9.0/page/nrf/protocols/thread/tools...
I have tried to debug my nordic5340 with VS code and it fails to load the code, although I'm able to flash the code using vs code.
when trying to track the problem using...
Hello,
I've come back to an existing project after a reboot of my computer and I'm now getting the error when I execute a build:
ImportError: Module use of python39...
https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals/lessons/lesson-6-serial-com-i2c/quizzes/lesson-6-quiz/
I think "i2c_read()" can only be used by I2C master...
Hi, how can i build and flash the Thread CLI sample code to my dongle? doesnt seems to work the .hex file? any links or steps tutorial i can follow closely please. i am setting...
