Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
I was under the impression that HomeKit was an extension of the MFi Accessory Interface Specification, which relies on the iAP protocol to access additional functionality...
Hi, I'm trying to run the ble_app_uart_s132_pca10040 demo but I can't get it to work.
We're using Keil 5.17 and downloading the example from the pack installer.
The packs...
Hi,
I always see HardFault when I debug a float point code. But it can run smoothly in run-time.
Firstly, I use code Style-1.
float val
val = (int32_t)NRF_ADC->RESULT;...
Hi,
We decided to add NFC functionality to our nRF52 open source sensor beacon design, RuuviTag: http://ruuvi.com
I would like to ask your opinion about the antenna...
I'm quite new to the Bluetooth development in gereral...
I want to design a Hardware using the nRF51 Dongle as the reference Design.
The plan is to take the Altium Files...
Hello Nordic Team,
i've get my things working and i figured out how i can set service data and to display it in nRF Master Control.
Now i want to CHANGE my service data...
Hi,
I'm wondering if I'am able to direct advertise when I have established connection (edit: according to this established connection nrf5x is master (central role))? ...
Hello!
everyone:
I use nRF51822 UART Demo(ble_app_uart),test uart interrupt receive data, baudrate is 38400.
if start advertising ,rx loss data ,else rx receive data perfect...
Hi,
I have develop my firmware on on nRF51DK which has n51422 chip.
But my actual hardware has n51822 chip.
So my firmware is working on development board (nRF51DK...
Hi Guys
I've got a strange problem where a binary that works fine on a nRF51822 QFAC does not run on a QFAA
I know that the difference between these two devices is the...
I need to define a few constant arrays for IR implementation. Currently, I define them as
static uint16_t but it takes up a lot of SRAM space. How do I move them to program...
Hi,
I have a setup (in SD310.2.0.0) on nrf51422-qfaae0 in which I'm hoping to receive data on multiple ant channels from multiple networks, but I cant seem to understand...
HI,
with the new version of the bluetooth website, i can not find the link to overview the profile,service,characteristic and something else related to it.
thank you.
Hello,
I am working on a wearable device at the moment. To support iOS and Android at the same time, I have implemented ANCS and nRF UART on the circuit.
When working...
