Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I'm trying to upload ble_app_beacon example from SDK 9.0.0 to a beacon board (PCA20006) after successfully uploading it to a DK board (PCA10028).
My first step was to connect...
I have created a customized Services according to nAN36 Document.
SDK using 8.0
Stack S110 8.0
DEV kit PCA10028 nRF51.
J-LInk RTT DEbugger
When the function...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Is there a step-by-step setup for the nrf52 developer kit for Mac (OS X)?
For example, when I connect my DK board, it does NOT appear as a USB drive which is the very first...
I've read through the 'streaming' posts and my need is a little different. I only need about 30 kbps streaming. I've created a service of this but am quite new to BLE and...
Hi all,
Is it possible to check whether there is an active carrier with the nRF24L01+? I've got the TX and RX chips configured via SPI correctly (I think), yet I can't...
What do I need to take care of when I solder CE pin to VCC? (to save I/O)
NRF is mostly in RXing state, and sometimes TXes.
So far I figured out to go from RX->TX mode...
Hi,
Can I use RTT to build a communicate to a command line interface (CLI) in the device?
This would require that the program does not block, as it does in SEGGER_RTT_WaitKey...
I'm using the UART application in nRF Toolbox Version 2.4, iOS 8.4 on an iPhone 5S.
Is it possible to save the logged data to a file, or in any other way get the data out...
Hello,
I am using an Eclipse GCC environment with the following setup:
Ubuntu -> 14.04 (Trusty Tahr)
Eclipse IDE for C/C++ Developers -> Version: Luna Service...
kit: RF51DK.
sdk:nRF51_SDK_8.1.0
SoftDevice:s110_nrf51_8.0.0_softdevice.hex
I want to use 5 channels pwm to control 2 servos and 1 motor;each servo uses 2 channels pwm...
I included the DFU service in my project. With the MCP on my computer it is working fine.
But when I try to perform the DFU over the MCP(v.3.4.1) app on my android device...
I'm migrating firmware from SDK 6.x to 9.0.0
I found pretty many changes in SDK APIs.
Do I have need or do you recommend to upgrade to new SDK ( for bugs / problems...
Hi!
I'm working with nrf51dk with s110 Soft Device.
I need to read ADC every 2ms. In order to achieve that, i made timer with interrupt after 2ms. here is my code of initialising...
