why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
I write this code to set my ble device power down,but it causes reboot without any error report.
GPIO_WAKEUP_BUTTON_CONFIG(LEFT_BUTTON_PIN_NO);
GPIO_WAKEUP_BUTTON_CONFIG...
I try to use 51822 to run ANCS sample(ble_app_ancs). It work well and I can get notification source and notification attributes. But I don't see any source code for get App...
Hi
I've a reproducable behavior i'm not able to explain. I'm using the softdevice S110 6.0 on a nRF51822.
The firmware implements some BLE profiles and uses TWI Master...
Is there a way to map external memory (SPI connected) to force the app to start execution from there ?
If not feasable , there is a way to transfer the execution from internal...
I have a 51422 board design and I just got Ant-FS working with our firmware so I can now download data from an external SPI flash to a desktop application.
I want to be...
Hello:
I am using NRF51822 to design somethings. And I want to use interrupt send method instead of polling send method.
NRF51822's UART0 provides TXDRDY interrupt. After...
Hi,
I have tested the nRF Toolbox proximity application using nrf51822 evaluation kit and with nexus4 smartphone it is working fine. Now my question is, is it possible to...
Hi
I am trying to overcome the problem that I have confronted, I have no buttons to delete bonds. So instead of deleteing this is what I did.
I modified the bondmanager...
I am developing hid_mouse . When I connect Android once and ubond hid_mouse I must set bluetooth off and on again to connect ble device otherwise it will connect again to...
Hi,
I am trying to set a value in the NRF_POWER->GPREGRET when softdevice is running, but it doesn't work. I don't get any error, but the value is always 3 and not 1 like...
Hi,
i took the example in AN36 (with the led but deleted the button stuff) and added the Battery Level service. Both are working fine together. On top of that I took the...
I have a development dongle PCA10000 , PCA10001 board and nRF pebble.
My aim is to come up with a project where one of these devices
a) would advertise,
b) the other...
Hi,
It has been mentioned in several threads that the MCP/dongle (on laptop) cannot support transmission of more than 1 packet per connection interval. Could you help clarifying...
