Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
I am new to designing with Nordic microcontrollers. I am at the point in my design where I am laying out connections to the microcontroller and setting up which pins will...
Dear Nordic-Support,
I have registered handlers for the two voltage level thresholds with the nrf modem library using modem_battery_low_level_handler_set and modem_battery_pofwarn_handler_set...
when I tried to add a device to nrf cloud, I am getting an error message 40101
My device is nrf9151dk with IMEI 359404230049133 and HWID 374155 I believe I might have registered...
I am exploring the possibility of using ncs v2.8.0 for Mesh with Coded PHY on the nRF52840dk/ nRF52840 board . I know this is not officially supported.
I started with the...
Dear,
I’m using nRF Connect SDK 2.7.0 with BLE Mesh and wondering how to adjust the TX power dynamically. When setting the TX power using a predefined option like CONFIG_BT_CTLR_TX_PWR_PLUS_8...
NCS 2.7.0
nrf52840
I'm currently porting software that was originally developed for nrf52832 on NRF5 SDK to run on Zephyr. I am currently on a deadline to delivery a prototype...
I've tried to follow the exercises from the Bluetooth Low Energy Fundamentals course. When I try to run the solution for lesson 3 exercise 2 I get the following error messagen...
Hello,
I have some previous code that ran using BT mesh. I then updated SDK's to 2.9.0 and I am now having issues provisioning devices. I am using the BT Mesh Provisioning...
Dear Nordic-support,
I am trying to use the modem_battery_low_level_handler and modem_battery_low_level_set(), but I think there are two different ranges for the battery...
Hi,
We are currently developing an application where we use a nrf52811. Currently i am working on integrating the BLE-Stack as this is the last part missing.
I am constantly...
Hello -
I am working through the DevAcademy - nRF Connect SDK Intermediate lessons. I have reached Lesson 7 Exercise 1, found here - https://academy.nordicsemi.com/courses...
Hi Team,
For my project, I am using nRF 5340 board and using the Zephyr SDK for development. I need to read and write data from/to an external QSPI EEPROM used ( MP95P08...
Smartbadge epaper custom board using nrf5340/nrf7002, with an NFC loop to allow NFC card emulation/communication. Building using NCS2.9 with sysbuild.
I want to be able...
Hi,
I just have a simple question => could you please tell me what are the ECCN numbers associated to this software:
www.nordicsemi.com/.../nRF-Connect-SDK
Thanks in...
-- west flash: rebuilding [0/16] Performing build step for 'tfm' ninja: no work to do. -- west flash: using runner nrfjprog -- runners.nrfjprog: reset after flashing requested...
